As shown in the figure, two aluminum rods AB and BC, hinged to rigid supports, are pinned together at B to carry a vertical load P = 6000 lb. If each rod has a cross sectional area of 0.60 in2 and E= 10 x 106 psi, compute the elongation of each rod and the horizontal and vertical displacements a = 30° and 9 = 30°. of point B. Assume

As shown in the figure, two aluminum rods AB and BC, hinged to rigid supports, are pinned together at B to carry a vertical load P = 6000 lb. If each rod has a cross sectional area of 0.60 in2 and E= 10 x 106 psi, compute the elongation of each rod and the horizontal and vertical displacements a = 30° and 9 = 30°. of point B. Assume

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Based on the figure below. Determine the required value of L if the force in member GE is equal to 517 N tension.
For the simply supported beam with the given cross-section, the shear force diagram has been plotted. Determine the maximum shear stress in section e-e of the beam. (A Note: the natural axis is located 65 mm above the toe of the cross-section and I = 5.8133×106 mm4) 160 mm |180 kN 20 mm - N.A B 100 mm 65 mm 500 mm 500 mm 30 mm 30 mm 20 mm V 90 kN Cross-section of the beam -90 kN
PLS SHOW COMPLETE FBD AND SOLUTION
Calculate for the axial force in kN at member GC of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
Please Kindly answer all
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?
The box beam in the figure is made of four pieces of wood nailed to each other as shown.Since the distance between the nails is 32 and the allowable cutting force on each nail is 160, (a=16, b=38, c=32, d=190, F=160) a) Maximum allowable vertical shear force in the beam? b) Determine the corresponding maximum shear stress in the beam.
Please answer the problem attached image. Hint: a=98.45Mpa
complete solution please 4 DECIMALS thank you Calculate the moment of inertia (in in^4). Calculate the bending stresses (in psi) at A. Calculate the bending stresses (in psi) at B. Calculate the bending stresses (in psi) at D.
4. The rigid bar AB is supported by two rods as shown and is horizontal before the load P is applied. Determine the vertical displacement of point which is 2 meters from the left support caused by the load P = 68 kN. Neglect the weight of the bar and the rods. Aluminum L= 3 m A = 300 mm? E= 70 GPa Steel L=4 m A= 500 mm? E= 200 GPa 3.5 m 2.5 m
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P = 1700 N, T = 4167 Nm, a = 0.94 m, b = 1.07 m, c = 0.98 m, w = 33 mm, and h = 79 mm . Round off the final answer to one decimal place. P T W Y U A/O А h B k a b C C | 1 D
Give me right solution.... Please urgent please