As shown in the figure below, a bicycle wheel is at rest against a curb. If the wheel has a radius R, mass M and is at rest against a curb of height h = 0.16R, determine the minimum horizontal force F (in terms of M and g) that must be applied to the axle to make the wheel start to rise up over the step. F = M

As shown in the figure below, a bicycle wheel is at rest against a curb. If the wheel has a radius R, mass M and is at rest against a curb of height h = 0.16R, determine the minimum horizontal force F (in terms of M and g) that must be applied to the axle to make the wheel start to rise up over the step. F = M

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A horizontal 790-N merry-go-round of radius 1.30 m is started from rest by a constant horizontal force of 45 N applied tangentially to the merry-go-round. Find the kinetic energy of the merry-go-round after 5.0 s. (Assume it is a solid cylinder. Also assume the force is applied at the outside edge.)
A hanging weight, with a mass of m, = 0.370 kg, is attached by a cord to a block with mass m, = 0.850 kg as shown in the figure below. The cord goes over a pulley with a mass of M = 0.350 kg. The pulley can be modeled as a hollow cylinder with an inner radius of R, = 0.0200 m, and an outer radius of R, = 0.0300 m; the mass of the spokes is negligible. As the weight falls, the block slides on the table, and the coefficient of kinetic friction between the block and the table is µ, = 0.250. At the instant shown, the block is moving with a velocity of v; = 0.820 m/s toward the pulley. Assume that the pulley is free to spin without friction, that the cord does not stretch and does not slip on the pulley, and that the mass of the cord is negligible. R2 (a) Using energy methods, find the speed of the block (in m/s) after it has moved a distance of 0.700 m away from the initial position shown. 2.15 x m/s (b) What is the angular speed of the pulley (in rad/s) after the block has moved this…
A solid cylinder with a mass of 15 kg and a radius of 5 cm is mounted on a frictionless horizontal axle over a well as shown in the Figure below. A rope of negligible mass is wrapped around the cylinder and supports a bucket with a mass of 3 kg. Find the bucket’s acceleration as it falls down the well shaft.
A thin rectangular plate is acted upon by 4 forces as shown. The 200 N makes an angle of 30 degrees with the horizontal. Calculate the net torque on this plate about the center A due to the four forces shown assuming there is no friction at the center. Note: (Angle at a is 30 degrees)
A hanging weight, with a mass of m, = 0.370 kg, is attached by a cord to a block with mass m, = 0.860 kg as shown in the figure below. The cord goes over a pulley with a mass of M = 0.350 kg. The pulley can be modeled as a hollow cylinder with an inner radius of R, = 0.0200 m, and an outer radius of R, = 0.0300 m; the mass of the spokes is negligible. As the weight falls, the block slides on the table, and the coefficient of kinetic friction between the block and the table is Hy = 0.250. At the instant shown, the block is moving with a velocity of v, = 0.820 m/s toward the pulley. Assume that the pulley is free to spin without friction, that the cord does not stretch and does not slip on the pulley, and that the mass of the cord is negligible. R2 R (a) Using energy methods, find the speed of the block (in m/s) after it has moved a distance of 0.700 m away from the initial position shown. m/s (b) What is the angular speed of the pulley (in rad/s) after the block has moved this distance?…
A horizontal 810-N merry-go-round of radius 1.20 m is started from rest by a constant horizontal force of 55 N applied tangentially to the merry-go-round. Find the kinetic energy of the merry-go-round after 2.0 s. (Assume it is a solid cylinder. Also assume the force is applied at the outside edge.)
A horizontal 810-N merry-go-round of radius 1.60 m is started from rest by a constant horizontal force of 55 N applied tangentially to the merry-go-round. Find the kinetic energy of the merry-go-round after 2.0 s. (Assume it is a solid cylinder. Also assume the force is applied at the outside edge.) ____J
A horizontal 810-N merry-go-round of radius 1.80 m is started from rest by a constant horizontal force of 55 N applied tangentially to the merry-go-round. Find the kinetic energy of the merry-go-round after 2.0 s. (Assume it is a solid cylinder. Also assume the force is applied at the outside edge.)