pls answer the given asap As shown in the figure, an air conditioner operating at steady state maintains a dwelling at 70°F on a day when the outsidetemperature is 103.5°F. The rate of heat transfer into the dwelling through the walls and roof is 30,000 Btu/h and the net power inputto the air conditioner compressor is 3.45 hp.Inside, 70° FEvaporator30,000 BrutRefrigerant loopCompressorOutsideCondensorDetermine the coefficient of performance of the air conditioner. Determine the power input required, in hp, and the coefficient ofperformance for a reversible air conditioner providing the same cooling effect while operating between the same cold and hottemperatures.

Answered: Image /qna-images/answer/1a6ff7d5-4a36-4e0a-92da-a3e6c3ade628.jpg

As shown in the figure, an air conditioner operating at steady state maintains a dwelling at 70°F on a day when the outside temperature is 103.5°F. The rate of heat transfer into the dwelling through the walls and roof is 30,000 Btu/h and the net power input to the air conditioner compressor is 3.45 hp. Inside, 70° F Evaporator 30.000 But Refrigerant loop Compressor Outside Condensor Que Determine the coefficient of performance of the air conditioner. Determine the power input required, in hp, and the coefficient of performance for a reversible air conditioner providing the same cooling effect while operating between the same cold and hot temperatures.

As shown in the figure, an air conditioner operating at steady state maintains a dwelling at 70°F on a day when the outside temperature is 103.5°F. The rate of heat transfer into the dwelling through the walls and roof is 30,000 Btu/h and the net power input to the air conditioner compressor is 3.45 hp. Inside, 70° F Evaporator 30.000 But Refrigerant loop Compressor Outside Condensor Que Determine the coefficient of performance of the air conditioner. Determine the power input required, in hp, and the coefficient of performance for a reversible air conditioner providing the same cooling effect while operating between the same cold and hot temperatures.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

when calculating the hc, why are adding the x as well ?
The answer should be 24,6kN when rounded up.
G tg Knowledge Check Answer the following. (a) Find an angle between 0 and 2x that is coterminal with 3 (b) Find an angle between 0° and 360° that is coterminal with-240°. Give exact values for your answers. JT (a) radians (b) IDon't Know Subnlit II
answer quickly
Calculate the rate of flow of waste thermal energy out of the engine in the exhaust gases in kW (to 1 decimal point). If the air inlet temperature is 35 °C, the air to fuel ratio is 10:1, the inlet air mass flow rate is 37 kg/hr, the specific heat capacity of exhaust gas is 1.13 kJ/kg/K, and the exhaust temperature is 500 °C. Add your answer Integer, decimal or E notation allowed
how did it become 0.1077?
If a critical point at structural element is subjected to the stress shown on the 2D element, determine the factor of safety (FS) against rupture according to the maximum principal stress theory. The material has an ultimate tensile stress Sult = 500 Mpa. 150 Mpa 50 Mpa 250 Mpa
Jensen Figure 6-71 Sketch 3 orthographic projections (i.e. top, front, right). Draw them on 10x10 cross section graph paper. - On each of the projections, label the inclined surface shown with its appropriate letter. - Identify if it is showing in first-angle projection or third-angle projection. b) a) K K Fig. 6-71 Sketching assignment 16.
Determine the absolute maximum shear stress of the stress state acting on the element shown in the following figure. 120 Mpa 300 Mpa 50 Мра
the reading in mm is L 3 O a 178 O b. 18.8 OC 27.8 O d. 28.85 re to search E
Given the table of results find the following. Give answers in KW. Please show all working out Rate of heat transfer to evaporator from the chilled water Rate of heat transfer from condenser to the cooling water Rate of heat transfer to refrigerant in Evaporator using enthalpy values Rate of heat transfer from refrigerant in Condenser using enthalpy values Work input from the compressor to the refrigerant using enthalpy values
This course A material having a shear modulus G, is deformed under a pure shear stress as shown in the following figure. Calculate the applied shear stress. Given: a = 1 mm, b Consider a linear elastic behavior. = 200 mm and G = 1.5 GPa. a 四