As shown below a wire loop is immersed in a B field ( the direction of the feild is show ) The beef field decreases from 20 T to 14 T and 7.8 seconds and as a result a 5.9 V voltage is induced The loops resistance is 5.3€ determine the loops radius and induced current

Q: Discuss the factors determining the induced emf in a closed loop of wire.

A:

Q: As shown below, a wire loop (that is immersed in a 0.43 T B-field) grows from a radius of 4.2 cm to…

A:

Q: The current in the RL circuit shown here increases to40% of its steady-state value in 2.0 s. What is…

A: The time during the steady state is, The current through the resistor during the charging is,…

Q: Scos (10't) âz mWb/m- a) find the induced potential in The Sem Sem 5quare wire b) If the B is tilted…

A:

Q: Below a wire is immersed in a B field the direction of the field is shown in the diagram the loop…

A:

Q: What is the direction of the induced current in each circular loop shown when the current I in the…

A: Here is the solution of your question:-Explanation:When the current in the long wire is decreasing,…

Q: www switch in the circuit shown in the figure above a battery suppoes a constant votage of E-30V,…

A: Given: Voltage V = 30 volts            Resistance R = 10 ohms            inductance L = 2 H To find:…

Q: If the loop has a resistance R which dissipates the energy as heat, what happens to the temperature…

A: Given that:

Q: As shown below, a wire loop is immersed in a 0.8 T B-field (the direction of the field is shown in…

A:

Q: 0.5: answer one of the following A) For the magnetic circuit in fig. 7 find the flux($) and the…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: In the circuit below, the resistance can be varied by turning a knob. If the resistance is slowly…

A:

Q: A conducting ring is held a certain distance above a loop carrying a decreasing current as…

A: If the current in the bottom coil is decreasing, there will be a change in the magnetic field in the…

Q: A0.850-m-long metal bar is pulled to the right at a steady 6.0 m/s perpendicular to a uniform,…

A:

Q: A wire along the z-axis (horizontal) with current I going in the positive z-direction produces the…

A: We know that the induced e.m.f e= -(rate of change of flux) Flux = B.A Where B is magnetic field and…

Q: At what speed (in meters per second) must the sliding rod in the figure below move to produce an emf…

A:

Q: following transformer circuit VSource=12.0volts, RSource=4, the number of turn on the left-handside…

A: Vs /Vp =Ns / Np

Q: decreasing current from left to right determine th ff.: a. at what point the potential is higher…

A: Given: decreasing current from left to right   To determine. a. at what point the potential is…

Q: Calculate L for the coil if the induced emf is measured to be 2 V for a call with 50 closed turns…

A: Given data: Induced emf =2VNumber of coil,N=50I1=0I2=5At=0.1 s

Q: Referring to the configuration shown on the right, a) determine the force between these conductors…

A:

Q: Current in a closed RL circuit How many seconds after theswitch in an RL circuit is closed will it…

A:

Q: A square loop of wire of side a contains a resistor R and a capacitor C. The loop sits in a…

A:

Q: A current 10 A in the primary of a transformer is reduced to zero at the uniform rate in 0.1 second.…

A:

Q: 1.4 Coil 1 Coil 2 (b)

A: An equation for induced emf across the two inductors given in figure. given,Current in coil 2=I2no.…

Q: . Sketch a graph of current value against time for two complete cycles of an alternating current of…

A:

Q: A transformer has 400 primary, and 80 secondary, turns. If an alternating potential of 250 V is…

A:

Q: Explain why the  current is the  same in all parts of a series circuit. Further, de- scribe why the…

A: According to Ohm's law," voltage drop in a resistance is equal to the product of current and the…

Q: J: Refer to figure la 2.0m conductor is shown, that rotates at 1200 rev/min in the radial field B =…

A: The formula to calculate the induced emf of given by the following expression, ε=-AdBdt where B is…

Q: As shown below, a wire loop with a radius of 0.84 m is immersed in a B-field (the direction of the…

A: A conductor placed perpendicular inside a magnetic field experiences a magnetic flux due to this…

Q: A solenoid having an inductance of 6.05 µH is connected in series with a 1.17 k2 resistor. (a) If a…

A:

Q: Sketch the current in an RL circuit over time.

A: Fig(a)   An RL circuit with a switch to turn current on and off. When in position 1, the resistor,…

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.