Armature resistance of a 230V shunt motor is 0.6 0 and no load current is 5A. When the rotor is loaded it is taking armature current of 60A. The speed is 1200rpm.Estimate the noload speed of a motor. O a. 1513.12 rpm O b. 1500 rpm OC 1400 rpm d. 1404.12 rpm

Armature resistance of a 230V shunt motor is 0.6 0 and no load current is 5A. When the rotor is loaded it is taking armature current of 60A. The speed is 1200rpm.Estimate the noload speed of a motor. O a. 1513.12 rpm O b. 1500 rpm OC 1400 rpm d. 1404.12 rpm

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Related questions

Q: A 200 V, 10 A, 1000 rpm, separately excited d.c. motor has an armature resistance of 3 Q. The motor…

A: Given data:Required information:The value of the duty cycle of the chopper.

Q: The Frequency of rotor eut of an 8-pole induction motor in 2HZ. If the Supply frego is 50 Hz, then…

A: The given data is shown below:

Q: 9. The synchronous speed of a three-Phase induction motor depends on the number of magnetic poles in…

Q: A) Why is the power factor of a lightly loaded 3-phase squirrel-cage inductio a) most of the power…

A: A. At light loads power supplied to induction motor consists of magnetization or reactive power…

Q: An eight-pole 60-Hz ac induction motor produces an output power of 2 hp and has rotational losses of…

A: Given data, The value of frequency of motor is f = 60 Hz. Number of poles P = 8. The value of…

Q: A 1200 rpm, 700V Series DC motor has an armature resistance of 20 and the field resistance of 90. If…

A: Efficiency = output power/ input power. Total losses = cupper loss + rotational losses.

Q: 2.. A three-phase 60 Hz asynchronous motor runs at 890 rpm at idle and 840 rpm at full load. ww w w…

A: Frequency f= 60Hz Speed 890rpm at idle Find the number of poles Slip at nominal speed What happed…

Concept explainers

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.

Question

Armature resistance of a 230V shunt motor is 0.6 0 and no load current is 5A. When the rotor is loaded it is taking
armature current of 60A. The speed is 1200rpm.Estimate the noload speed of a motor.
O a. 1513.12 rpm
O b. 1500 rpm
Oc 1400 rpm
O d. 1404.12 rpm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Define the given data :

VIEW

Step 2: Armature voltage at loaded and unloaded condition :

VIEW

Step 3: Calculation of speed at no load condition :

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. The operation of Commutator in DC Motor is * O a) to convert dc to ac O b) to convert ac to dc O c) to convert fixed dc to variable dc O reverse the current direction in the rotating windings each half turn
A 220V dc shunt motor takes 4A at no load and runs at 700 rpm. Ra = 0.60 ohm and Rsh = 110 ohms. What is the efficiency of the motor when the motor input is 8800 W? a. 81.67% b. 80.2% c. 82.05% d. 79.44%
7 Multiple Choice 10 points The shaft torque of a dc motor is less than its armature torque because of Copper losses Mechanical losses Back emf Rotational losses
A 250 V series motor has an armature resistance of 0.2 ohm and a series-fieldresistance of 0.18 ohm. If the speed is 6oo RPM when the current is 32 amps.What will be the motor speed when the load is reduced so that the current is18 amps, under which condition the percent flux change is 50 % of the percentcurrent change.
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
pole. 50-Hz. 3-ϕ induction motor has a full-load speed of 950 rpm. At half load its speed would be ..... rpm a) 475 b) 500 c) 975 d)1000
The supply frequency to the stator of an 8-pole induction motor is 50 Hz, and the rotor frequency is 3 Hz. Determine the slip and the rotor speed.
A 15 HP 220 V shunt motor has an armature resistance of 0.07 ohm and shunt a shunt resistance of 200 ohms. The overall efficiency at rated output is 89 %, What is the rotational loss?
Please question 4
An increase in the torque angle a results in: O A. No change in the induced torque O B. Decreasing the induced torque O C. Decreasing the load on the synchronous motor D. None of the other choices are correct O E. Increasing the induced totque
An eight-pole 60-Hz ac induction motor produces an output power of 2 hp and has rotational losses of 100 W at a speed of 850 rpm. Determine the slip, the frequency of the stator currents, the frequency of the rotor currents, and the rotor copper loss.
need asap A dc series motor runs at 1000 rpm when taking 20-A at 200-V. Armature resistance is 0.5-ohm. Series field resistance is 0.02-ohm. Find the speed for a total current of 20-A when a diverter resistor of 0.2-ohm is used across the series field. Flux for a field current of 10-A is 70 % of that for 20-A.