Argon (100 kPa and 10 deg C) enters a compressor with a mass flowrate of 0.19 kg/s. It exits at 600 kPa and 130 deg C. The compressor has a specific heat loss of 16 kJ/kg. What is the power (kW) required for the compressor? Report your answer to 2 decimal places.

Argon (100 kPa and 10 deg C) enters a compressor with a mass flowrate of 0.19 kg/s. It exits at 600 kPa and 130 deg C. The compressor has a specific heat loss of 16 kJ/kg. What is the power (kW) required for the compressor? Report your answer to 2 decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.2 1 kg of a fluid is compressed reversibly according to a law pu= 0.25, where p is in bar and v is in m'/kg. The final volume is done on the fluid and sketch the process on a p-r diagram. of the initial volume. Calculate the work (34 660 Nm)
1) A 10 Liter pressure cooker has an operating pressure of 400 kPa. Initially, % of the volume is filled with saturated water and the rest is saturated vapor. What temperature is the vessel? After heating for 5 hours, the pressure cooker ran dry. What was the average rate of heat transfer?
QUESTION 38 In an experiment, a certain amount of air is heated at constant pressure from 1.7 m³, 30 ºC and 97 kPa to 423 'C. It is then cooled at constant volume back to its initial temperature. Calculate the change specific entropy in the constant pressure process in the correct unit in SI and 1 decimal place. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJ/kg K respectively. Add unit. 1 decimal place.
Phy
There is 3.5 L saturated liquid water at 175 kPa pressure in the frictionless moving piston-cylinder system shown in the figure. The heat given to the system is 500 kJ and the electrical work is 1320 kJ. Since half of the water evaporates at constant pressure; a) Write the energy balance equation (First Law), b) Calculate the mass (kg) of water, c) Calculate the required shaft work (kW), d) Show the process in T-v and P-v diagrams, including saturated liquid and saturated vapor curves
Solve correctly please.
37. A certain gas with Cp = 2.215 KJ/kg °K and R= 0.518 KJ/kg °K with a volume of 0.425m3 and 300 °K has an initial pressure of 106.869 KPa.Heat is added at constant volume until the final pressure becomes 387.72 KPa. How much heat is added?
Oxygen (molar mass 32 kg/kmol ) expands reversibly in a cylinder behind a piston at a constant pressure of 3.176 bar. The volume initially is 0.0119 m3 and finally is 0.032 m3; the initial temperature is 17.83 0C. Calculate the heat supplied during the expansion in the correct unit to two decimal places. Assume oxygen to be a perfect gas and take the specific heat at constant pressure as = 0.917 k J / k g K and molar gas constant as = 8,314 J / kmol K
Q) A & B are rigid tanks. Tank A has volume of 1 m3 , contains steam with 4 MPa and 500 °C heated by external heat source with 130 kJ. The valve is open allowed to part of steam exit from the tank A to an evacuated and insulated tank B at constant temperature, then the valve is close when the final pressure in tank A reaches to 2 MPa and the mass reduce by 2/3. Determine the volume of tank B. A в
c. Before going to school and attend his physics class, an engineering student fills the 60-L steel tank of his brand new car with gasoline at 60°F. The car is left in the sun in the school parking area, and the temperature of the gasoline rises to 110°F. Approximately how much gasoline is lost to overflow caused by thermal expansion. Consider the expansion of the tank.
3) A tank, well insulated, has two parts divided by partition. The first part incuded 3,5 kg of water at 800 kPa while the other part is evacuated. This partition is removed and the water expands to fill the entire tank. If the final pressure and temperature are 100 kPa and 200°C, respectively, please determine a- The volume of the tank b- Temperature of the water for first part
steam at a temperature of 250°C has a specific volume of 0.15436m³/kg.What are the pressure, specific internal energy, entalphy,and entropy?