Question #4 A rigid tank with a volume of 2-m³ initially contains air at 100 kPa and 30 °C. The tank is connected to a supply line through a valve. The inlet air flows at 600 kPa and 25 °C. The valve is now opened, and air enters the tank until the pressure inside the tank reaches the pressure of the inlet supply, at which point the valve is closed. The air temperature at the final state is 77 °C. Determine the entropy generation if atmospheric temperature is 298 K. P₁= 600 kPa T₁= 25°C V= 2 m³ P₁ = 100 kPa T₁=30c lout

Q: Worksheet 6-3 00 1. Type of view 2. Type of view 3. Type of view 4. Type of view 5. Is view 4 easier…

A: Solution: Given Data:

Q: Prioritize the following line types. If a line type is prioritized, that means that it will be…

A: Given Lines To find Highest priority line in engineering drawing

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: Sketch the orthographic projection as per the answer arrangement (a) top view (b) side view (C)…

A:

Q: For the following figure assume the box as 10 mm and sketch the following view using CREO PARAMETRIC…

A:

Q: n an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

A: For the solution refer below images.

Q: Given the multiview projection of the solid, draw the isometric view.

A: Given:To find:Draw the isometric view.

Q: Sketch the right oblique view name front view(F) and top view(T) and side view (S) on the sketch…

A:

Q: Draw the orthographic views of the following isometric figure

A: Given  3D model isometric view To find Orthographic view

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: Given the two views of a solid and an auxiliary reference plane, draw the auxiliary view and…

A: Draw Auxiliary view of the given figures.

Q: Draw the isometric and orthographic sketch of the given figure (in catia V5 ;no hand drawing );

A: isometric view

Q: Create alineBOMline, arc, or any other drawing which has an endpoint or sharp comers, Afterward,…

A: Given :-  create a line, arc , poly line or any other drawing which has an end point or sharp…

Q: SKETCH THE 2D FIGURE IN AUTOCAD DRAWING AND USE THE 2D SKETCHING TO FIGURE OUT THE BELOW SKETCH

A:

Q: Sketch the isometric view Sketch the first angle orthographic view Note:use creo parametric to…

A:

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: 35 86 $ 38 51 20 R10 105 16 F

A: Given 3D model To find Orthographic view

Q: A Sluice gate is a device that is fitted in a sluice or fluid canal to operate and control the fluid…

A: We need to calculate the hydrostatic force acting on the sluice gate

Q: Given the left and front views, sketch the top view.

A: The problem is easily done with the help of orthogonal projection. first try to imagine the 3D view…

Q: Pls provide the sectional view below

A:

Q: PART-A (Sectional View - SKETCHING) 1. Reproduce all two views given and add/complete the sectional…

A: Given Diagram To find Sectional views

Q: Draw the isometric figure given the views below. Will thumbs up if correct. Thank you.

A:

Q: Draw front, top and then left side view.

A:

Q: Circle the letter corresponding to the correctly aligned set of orthographic views. 1. 2. A 6:6 A E…

A: according to the drawing data we need to find, the right option. that represent the three…

Q: CONFIDENTIAL 03. Draw the missing lines (Hidden Line & Center Line) on the orthographic view in…

A:

Q: Sketch a isometric drawing for each of the three sets of orthographic drawings

A: Given: A set of orthographic projections.

Q: drawing all the views

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: DRAW THE MULTIPLE VIEW

A: The given view is in isometric view

Q: sketch the orthographic view of the given figure below

A:

Q: Sketch the orthographic view Top Side and Front Using engineering graphics drafting

A:

Q: Given TOP VIEW & FRONT VIEW sketch the side view and isometric view Note : Assume each unit as 10 mm

A:

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: 1) The density of a metal, which has the BCC structure and one atom per lattice point, is 0.855…

A: given data: density of metal in bcc structure=0.855g/cm3 atomic weight =39.09g/mol

Q: ZATION & ENGINEERING Design GraPhics with AuGmented REALITY

A: Sectional view

Q: sketch the 2d figure using autocad and colour the hatching and reference lines

A:

Q: QI: Draw the orthographic Projections of given object. 20, 26 20 14 R20 35 SHOT ON REDMI 7 AI DUAL…

A: Orthographic projection is a two-dimensional representation of three-dimensional objects. It's a…

Q: Given the top and front views, sketch the right face.

A: According to the details provided in the question. Top view and front view is given we need to draw…

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.