A)plot the de load line for the PNP transistor shown in the next figure. Assume the transistor parameters are: RE = 10 k2 VEB (on) = 0.7 V, B = 150, and VA VEB %3D Rs =1 ka CI wwHH CE =00. Assuming that (1 + B)/B=1. B) Assuming that all capacitors act as short circuits once AC input is connected, sketch the small-signal equivalent circuit, and plot the AC load line. Find r7 , and gm. find (fo) and find The small-signal output voltage, or C-E voltage, Cc2 Rg= 50 k2 R = 2 ko ER%3D :5 ko V=-10 V

A)plot the de load line for the PNP transistor shown in the next figure. Assume the transistor parameters are: RE = 10 k2 VEB (on) = 0.7 V, B = 150, and VA VEB %3D Rs =1 ka CI wwHH CE =00. Assuming that (1 + B)/B=1. B) Assuming that all capacitors act as short circuits once AC input is connected, sketch the small-signal equivalent circuit, and plot the AC load line. Find r7 , and gm. find (fo) and find The small-signal output voltage, or C-E voltage, Cc2 Rg= 50 k2 R = 2 ko ER%3D :5 ko V=-10 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A sinusoidal voltage of 48v, 60 Hz is applied to a half-wave rectifier with dynamic resistance of the diode of .001ohms turns ratio (3:1). Calculate the DC and RMS currents flowing through the load(R=210 ohms). Also calculate the dc output power developed, ac – input power supplied, rectification efficiency, and ripple factor.
In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
VoO for Ma mosfet Nn Cox ( )= Jm Alv? ,Vrw=0,7V J00NA (+) VX %3D %3D a) In uhat condition does the mosfet work ?and frnd the voltage Vx= ? M1 3V b) what is the mompmum Voo voltage and why'?
1) In the context of semiconductors, describe the following:(a) Intrinsic and extrinsic semiconductor. (b) Drift velocity of carriers.(c) Band-gap energy.(d) Frequency of light emitted by an LED.
Design a POWER SUPPLY with 5V output voltage. Use zener diode as a voltage regulator. Then solve for theoretical computations. Thanks!
A PWM signal changes with a voltage of -15 and 15 volts while it is desirable to produce an effective (average) voltage of the PWM signal of 9 volts. The duty cycle that must be generated is
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
Q5(a) Figure Q5(a) shows a basic series voltage regulator circuit. VIN VOUT RREF Q1 U1 R $20 k2 Di R2 30 k2 Figure Q5(a) (i) Calculate the output voltage, VoUT if VIN = 50 V and voltage drop across D, = 6.2 V. (ii) Illustrate a circuit diagram for overload protection between transistor Q1 and the load. (iii) Based on the answer in Q5(a)(ii), calculate the overload current ILmax). (b) Figure Q5(b) shows a voltage regulator. +35 V LM 317 +Vout R1 Vref 220 2 Iref C3 C1 TR2 TADJ C2 R2 5 kn Figure Q5(b) (i) Determine the maximum and minimum output voltage for the voltage regulator in Figure Q5(b), if IADJ = 25 µA and Vref = 0.9 V. (ii) Determine the output voltage of the regulator if R2 is set to 4 kN.
8-The waveform of output voltage of half-controlled three phase bridge rectifier in each cycle contains: Two- pulse six- pulse three- pulse 9-The DC supply voltage of single phase bridge inverter is 300V. For quasi-square wave output voltage with a 60 percent ON time, the RMS value of output voltage is: 232.37V 220.5V 270.9V 10-For three phase bridge inverter with 120° conduction and resistive star-connected load, the waveforms of: (a) The load current and line voltage are quasi-square. (b) The load current is quasi-square and line voltage is a six- step. (c) The load current is six- step and line voltage is quasi-square. 9.
A centre-tap full-wave rectifier (CT-FWR) is operated from a (60 Hz), (110 V,ms) line voltage through a transformer with turn ratio of ( = 2). It has a (2 k 2) load resistance. Assume Si diodes. 1. What minimum value of capacitance is required if the ripple must be no greater than 1%? 2. If the filter capacitor is changed to a (470 µF), what is the required load resistance to give the same ripple of 1%. 3. Determine the DC voltage on the load side. 4. What is the power dissipated and minimum PIV of each diode? 5. Draw the circuit diagram with output voltage waveform.