APCB circuit using 2n3904 transistors is used to construct a Darlington-pair input circuit as shown below. Assume Br= 100. The Early voltage for the transistor is 75V. Determine the ECP circuit a) input resistance Select Rin MQ. b) Differential Voltage gain Select) * Avs ) Commom Mode Rejection Ratio Select in dB

APCB circuit using 2n3904 transistors is used to construct a Darlington-pair input circuit as shown below. Assume Br= 100. The Early voltage for the transistor is 75V. Determine the ECP circuit a) input resistance Select Rin MQ. b) Differential Voltage gain Select) * Avs ) Commom Mode Rejection Ratio Select in dB

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question three: Given the BJT transistor characteristics of Figure below: a. Draw load line on the characteristics determined by Vcc=21 V and R= 3 kQ for a fixed- bias configuration. b. Choose an operating point midway between cutoff and saturation. Determine the value of Rp to establish the resulting operating point. c. What are the resulting values of Ico and Vceq? d. What is the value of ß at the operating point? e. What is the value of a defined by the operating point? f. What is the saturation current (Icsar) for the design? g. Sketch the resulting fixed-bias configuration. h. What is the dc power dissipated by the device at the operating point? i. What is the power supplied by Vcc? j. Determine the power dissipated by the resistive elements by taking the difference between the results of parts (h) and (i). 1 Ic(mA) 110HA 100 µA 10 9 40 µÃ 5 30 HA 4 20 μΑ 10 HA 10 15 20 25 30 VCE (V)
With the help of circuit diagrams, list the different biasing methods for D- MOSFET and E-MOSFET amplifiers.
1. To use the Bipolar Junction Transistor (BJT) as a small signal amplifier it must be biased in this region: A. South Park region B. Spatial interface region C. Inverse Thevenin region D. Linear or active region
Cmrr
Determine small signal voltage gain if VCEQ = 4.5 V. Transistor parameters (NMOS): k,= 100 µA/V² , VTN=1 V, and 1 = 0.01 V. Transistor parameters (BJT): B = 100 , VBE(on)= 0.7 V, and VA = 00 . 10V 8V Vo VIN
16. Determine IB, Ic and VCE for a base biased transistor circuit with the following values; Bpc= 90, Vcc=12V, RB=22kN, and Rc=1002. 17. A collector-feedback circuit uses an npn transistor with Vcc=12V, Rc=1202, and RB=47KN. Determine the collector current and the collector voltage if BDc=200. 18. For the fixed-bias configuration of Fig. 13, determine: IBQ, Ica, VCea, Vc, VB, and VE. +8V R 360k Rc Vo B= 100 Fig. 13 19. For the voltage divider bias configuration of Fig. 14, determine: IBa, Ica, Vcea, Vc, VB, and VE. +16V R, 62k Rc 3.9k O v. B = 81 9.1k RE 0.68k Fig. 14
estion 2: Consider the BJT circuit given here. ( Write the input and output loop equations For the given values of Vcc= 10 V, Vin = 4V and resistor values, calculate all current values (IB, IC and IE) and VCE Assume that the ß for the transistor is 100 and the voltage drop across LED connected between Collector terminal and resistor (Rc) 2.1 V. TH i. ii. 111. VIN Vcc Rg=100 kΩ Re=2 kΩ LED 2.1 V B= 100 Based on the above analysis, correctly identify the current mode of operation Cutoff mode Active linear mode Saturation mode
Design a voltage divider biased CE stage with emitter degeneration. That stage should support a voltage gain of 5 and an input impedance larger than 3 KOhms with a bias current of 0.5 mA. Assume Beta=100, Is = 5e-17. Neglect the early voltage effect. You also need to provide values for the operating point of this transistor. Find the output resistance of this stage if the early voltage = 20 V.
I need the answer quickly
To operate as an amplifier, it is the base of an npn transistor... Please select one: a. 0V b. positive by collector c. negative relative to emitter d. positive relative to emitter
Refer to the differential amplifier circuit shown below . Determine the quiescent DC voltage at the collector terminal of each transistor assuming VBE of two transistor are negligible. What will be the quiescent DC values if VBE is taken to be 0.7 V.
Please type answer note write by hend.