-) Answer the following questions and justify your answers. a) is the system given by y(t) = x(-t) + x(t)² représent a stable system? Is it a linear system? yes it stable broms it stable brooms for my Bour tment, x²-1)+20 21 2+2 M4 M Lodo XU 7+%₂6+ [4]+X+X →→→[5] →y= 2;H+14 %;H?! ) + (2x) + 25 +² Y Y b) is the following system, y(t) = sin(t)x(t), linear? Is the system time- invariant? = Smutjy Sint Xit) Sort Y fu 3 ay sin f(xicj+X+]) say=Y₁+/ sing kell ky, z kimbalj so sky 3/3(0-10) 34 3 14_10)-g-y- Sint Deittuj yitky)=sin( વડા (લ *Hata c) What is energy of the signal is given by x(t) = t(u(t)- u(t-2))?

-) Answer the following questions and justify your answers. a) is the system given by y(t) = x(-t) + x(t)² représent a stable system? Is it a linear system? yes it stable broms it stable brooms for my Bour tment, x²-1)+20 21 2+2 M4 M Lodo XU 7+%₂6+ [4]+X+X →→→[5] →y= 2;H+14 %;H?! ) + (2x) + 25 +² Y Y b) is the following system, y(t) = sin(t)x(t), linear? Is the system time- invariant? = Smutjy Sint Xit) Sort Y fu 3 ay sin f(xicj+X+]) say=Y₁+/ sing kell ky, z kimbalj so sky 3/3(0-10) 34 3 14_10)-g-y- Sint Deittuj yitky)=sin( વડા (લ *Hata c) What is energy of the signal is given by x(t) = t(u(t)- u(t-2))?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer quickly
Saved Messages Shared media A premaccs = Pinned message | fr12345@notavaaq.ga - 10 un fiveunl@notavaaq.ga - 10 un SOLD 77 videos A 12 resistor is connected in series with a 2mH inductor. if a 12-V dc source is suddenly connected across its terminal, how long will it take, such that the voltage across the resistor will be twice as that of the inductor. A 2.5 ms B) 1.7 ms (c) 2.2 ms D 1.9 ms E ELYSIAN MARKET kay @premsbyjisoo mag dm: AVAIL 180 4 UNIQUE MARKET Photo 314 of 317 ava today at 11:56 AM Upload Docu. 0 O Spotify
Advanced Physics In the circuit, Xm = 1.50. We want to determine the input impedance seen between terminals a and b. We therefore connect a test voltage, VT, where the ratio between VT and IT gives the input impedance Zin. a) Štart by replacing the transformer and the 0.50 resistor with only one resistor. b) Write up the mesh equations for the resulting circuit. Xm 2:1 J3 N j20 0.5 A Figur 10 c) FindZin = VTIT.d) Calculate the complex power transferred to the 0.50 resistor, if VT = 1Vrms
answer in 6 decimal places.
2. A parallel plate capecitor has A interleaved plates each 75mm by 75mm separated by mica sheets mm thick. Assuming the relative permittivity of the mica is and the voltage between them is D kV.Calculate the canacitance of the capacitor and total charge accumulated on the capacitor.
Saved Messages Shared media A premaccs = Pinned message fr12345@notavaag.g O un SOLD 77 videos An uncharge capacitor in series with a 120-volt voltmeter os 10,000 ohms resistance is suddenly connected to a 100V battery. one second later, the voltmeter reads 60 volt. Determine the capacitance of the capacitor A 187.54 uF B 190.62 uF 197.76 uF D 192.23 uF * UNIQUE MARKET kay @premsbyjisoo mag dm: AVAIL 271 & TG SCAMMERS GC Photo 313 of 317 Upload Docu. 0 Spotify ava today at 11:56 AM WebAdvisor
For the given circuit below: a) Total Resistance,total Inductance,total capacitance and the total Impedance in polar formb) The total current in polar form and the voltage across resistor,Inductance & the capacitor.c) Draw all voltages and current on the Complex Plane.
Find the current I1 and the charge stored in capacitor C2 for steady state.
Consider the parallel and series combinations of the capacitors shown below. What is the equivalent capacitance between the terminals a and b. 6 F C₁ 6 F C1 3 F C2 82 + VC b I HE b 1₂ + VCI +1 VC2 3 F وتا Ceq 1. B Cea b b 16+ VC +
Place your final answers for this problem in the correct boxes at the bottom of the next page. Use the value Zdegrees notation for representing phasors. Bold terms are expected to be phasors. Tek Run 1 5.00 V 8 4.00ms +6.68000ms 4 H a b 3.29ms 20.0ms A16.7ms (2.50MS/S 100k points The voltage pictured in the image above is applied to a load with an impedance of Z=3+j5. The load has two components, in series. 1 1. What is Vmag and Vrms. Assume that the phase of the pictured waveform is degrees. 2. Calculate Irms. 3. Calculate S, the complex power. Trig'd 9.425 V 9.429 V A3.906mV s 3.00 V 4. Calculate average power, apparent power, reactive power, and power factor. It isn't necessary to list if the power factor is leading or lagging. 5. What component values are used to make the resistive and reactive components of the load?
please show step by step calculations for the attached question. and state all equations used
Consider the state space representation of the system [-1 0 X = X+ -2 y =[0 1]X The system is completely (a) Controllable, Observable (b) Controllable, Not Observable (c) Not Controllable, Not observable (d) Not Controllable, Observable