Answer the following questions:1. A clean circular glass tube is to be selected in the design of a manometer to measure the pressure ofKerosene . Specific gravity of kerosene = 0.82 and surface tension of kerosene = 0.025 N/m. If thecapillary rise is to be limited to 1 mm, the smallest diameter (cm) of the galss tube should be mostnearlya) 1.35b) 1.5c) 1.75d) 2.002. Both a gage and manometer are connected to a gas tank to measure its pressure. If the reading on thepressure gage is 80 kPa. The distance between the two fluid levels of the manometer h is..... if the gage fluid in the manometer is a mercury (s 13.6); and h isif the gage fluid in the manometer is water.a) 0.4 m; 9mb) 0.9m; 4.3 mc) 6.213m; 0.7626 md) 4.91m; 0.668mP= 80 kPah = ?3. A 50-ton, 6-m diameter hemispherical dome on a level surface is filled with water as shown infigure. An engineer claims that be can left this dome by attaching a long tube to the top and filling itwith water. So, the required height of water h in the tube to lift the dome isthe weight of the tube and water therein.Ignorea) 0.47 mb) 7.4 mc) 3.765 md) 0.935 m

Answered: Image /qna-images/answer/da738949-73a8-4ae3-b7d5-989d8422c48d.jpg

Answer the following questions: 1. A clean circular glass tube is to be selected in the design of a manometer to measure the pressure of Kerosene . Specific gravity of kerosene = 0.82 and surface tension of kerosene = 0.025 N/m. If the capillary rise is to be limited to 1 mm, the smallest diameter (cm) of the galss tube should be most nearly . a) 1.35 b) 1.5 c) 1.75 d) 2.00 Both a gage and manometer are connected to a gas tank to measure its pressure If the reading on the

Answer the following questions: 1. A clean circular glass tube is to be selected in the design of a manometer to measure the pressure of Kerosene . Specific gravity of kerosene = 0.82 and surface tension of kerosene = 0.025 N/m. If the capillary rise is to be limited to 1 mm, the smallest diameter (cm) of the galss tube should be most nearly . a) 1.35 b) 1.5 c) 1.75 d) 2.00 Both a gage and manometer are connected to a gas tank to measure its pressure If the reading on the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left limb is open to the atmosphere and the right limb is connected to the pipe. The center of the pipe is 61 mm below the level of mercury in the left limb. If the difference of mercury level in the two limbs is 147 mm, determine the gauge pressure of the oil in the pipe in Pascal. The specific gravity of the oil & mercury is 0.79 and 13.6 respectively. Solution: (i) Density of oil in kg/m3 (ii) Density of mercury in kg/m3 (iii) Height of the Oil in the right limb (in meters of oil) h1 (iv) The gauge pressure of the oil in the pipe in (in Pascal)
1. Water is flowing in a wide open channel as shown in the figure. Two pitot tubes are connected to a different manometer containing oil (sp.gr. = 0.82). Find the velocity at m point A and point B in - oil (op.gr.=0.82) 2 m wafer sarfece
please provide a clear and correct solution, thanks!
A 3mm Ø tube is inserted in water. Assuming a clean tube and the angle of contact with water is 0°, what is the amount of capillary rise if surface tension is 0.0728 N/m?
A mercury Manometer is attached to a pipe having suction pressure. The right limb is open to the atmosphere while the contact between mercury and water is in left limb at a distance of 30 cm from the center of the pipe. a. If the difference in the Level of mercury in the two limbs is 20 cm, What will be the pressure in the pipe. b. If the pressure in the pipe is increase to Pascal, What will be the new difference in mercury level?
Q- A mercury water manometer has a gauge difference of 0.8 m. The difference in pressure measured in metres of water is..
3. Consider the following scenario: A civil engineering stadent measures the resistivity of a particular cytindrical wire for different lengths L by tapping at points the wire from 0.l m to 1 m in steps of 0.1 m The radms of the wire is 0.02 mm. The experiment is carried out under following circumstances: a) The best line has been drawn through the points given below and determine the resistivity of the wire from the slope of the plot between blue marked points. b) Based on the vahue of resistivity you calculated, what is the material wire resistor made of? Make sure everything is in ohms and meters, otherwise your units will not work out correctly in the end! Table 1. Resistivity of Some Common Materials. Material Silver Соррer Gold Aluminum Steel Lead Manganin (Cu. Mn. Ni alloy) Constantan (Cu, Ni alloy) Mercury Nichrome (N. Fe. Cr alloy) Resistivity p ( N-m) 1.59x 10 1.72x10 2.44 10 2.65x10 2x10 22x10 4.4x10 4.9x107 9.6x10 1-10 9. 8 7- 6- 5. 3. 2. 00 0.2 0.4 06 08 Lim)
Please correct solution
A U-tube manometer is arranged, as shown in Fig. 2.15, to measure the pressure difference between two points A and B in a pipeline conveying water of density 1000 kg/m³. The density of the manometric liquid Q is 13600 kg/m³ and point B is 0.3 m higher than point A. Calculate the pressure difference when h = 0.7 m. T Manometric liquid Q of density Pman Figure 2.15 Measurement of pressure difference Fluid P, of density blup all to 20 lens
... EX, 7 The device shown in the figure is known as a venturi. In this specific venturi, the differential pressure between locations 1 and 2 is 30 kpa and the diameter ratio is D2/D1 = 0.35. If D2 = 16 cm, find the air flow rate through the frictionless venturi. 12 THR (2) (1)
This is a mercury U-tube*acceleration = 4.905 m/s^2 to the right What is the gage pressure at A? in kPa
I need the answer as soon as possible