Answer the following 3 questions based on the Gerber Girder System with the loads shown. Note: the value of Pis randomly generated and will most likely be different for each question. P (kN) 200 kN 200 kN w 20 kN/m w= 15 kN/m hinge hinge 6m 6m 2m 4m 4m 2m 3m 6m 3m R1 R4 R2 12 m 12 m 12 m Left beam with right side overhang Drop-in Panel Right beam with left side overhang

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: What the center of gravity

A:

Q: Jse commands (rectangle, mirror) and List he commands to draw the following drawing start from a…

A:

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: entify the outfall entify the peaks entify the valleys

A: Watershed: A watershed depicts an area of land that contains a typical arrangement of streams and…

Q: y 500 50 80 -140- - 140- 80 60 400 500 50 500

A: Given- plate area is given  To find- centroid of given plate area

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: You are a professor of architecture. Show your students where the horizon line and vanishing points…

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: 4 in 2 in 4 in 8 in -12 in- -16 in-

A:

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: Draww SED8 B.M.D The 4000N 5M 5 m

A: given beam

Q: CEM I 52.5 N: Define what each word/number/letter is?CEM I: .... 52.5: .... N: .... ....

A: Brief concept- This CEM I 52.5 N is related to the cement and its types and classification. The…

Q: 80 mm -L- В D 60 mm

A:

Q: Z 10 mm 15 15 430 y y -y y 15 100 All dimension in mm FIGURE Q3 (a) FIGURE Q3 (b) IN

A: The dimensions of channel section are given.two channel sections are arranged back to back with 10mm…

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: Determine the coordinates of the centroid of the shaded area. y 15 E 30 35 15 40 50 I 30 - x 100…

A:

Q: The representation of the hinge lines of the glass box in a drawing are known as lines. ....** .....…

A: The glass box concept is used in orthographic projection. When the glass box is visualized, then…

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: Y

A:

Q: Explain why wx = 2/3(9-x)

A: Given:Required:To explain loading intensity for 6<x<9