Answer Q1. A. Inside a 60-mm diameter cylinder a piston of 59 mm diameter rotates concentrically. Both the cylinder and piston are 80 mm long, as shown in Fig. If the space between the cylinder and piston is filled with oil of viscosity of 0.3 Ns/m² and a torque of 1.5 Nm is applied, find the rpm of the piston. y 0.0005 mm L 80 mm 3-59 mm D-60 mm Piston Cylinder

Answer Q1. A. Inside a 60-mm diameter cylinder a piston of 59 mm diameter rotates concentrically. Both the cylinder and piston are 80 mm long, as shown in Fig. If the space between the cylinder and piston is filled with oil of viscosity of 0.3 Ns/m² and a torque of 1.5 Nm is applied, find the rpm of the piston. y 0.0005 mm L 80 mm 3-59 mm D-60 mm Piston Cylinder

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

need help
Situation I: In figure shown a pulley is subjected to a torque whose value is 420 N- m. The coefficient of friction between the belt and the pulley is 0.40 1. What is the value of T1 to impend slipping? 2. What is the value of T2 to impend slipping? 3. What is the value of the horizontal reaction at the hinge? 0.27 m 420 N-m
A 140 mm height of cylinder of 70 mm diameter is used as a short column and carries a pressure of -100 MPa as shown in below. Knowing that E= 105 GPa and u = 0.34,
Compression spring.
no. 1 *Equilibrium of Rigid Bodies
The bent rod shown in (Figure 1) is supported at A, B, and C by smooth journal bearings. The bearings are in proper alignment and exert only force reactions on the rod. Figure 2 m 30° 60° F B 1 m C 1 of 1 2 m 0.75 m art A Determine the magnitude of F which will cause the positive a component of reaction at the bearing C to be C = 30 N. Express your answer to three significant figures and include the appropriate units. F = Submit Value Provide Feedback Request Answer Units ?
statics of rigid bodies
TNT a 8 95% D7:20 Q44 D137 PROBLEM SET NO. 1_STRESS ANALYSIS_SIMPLE STRESS.pdf 1. As shown below, two pneumatic cylinders are used to control the motion and displacement of the device arm ABC. Assuming that the control rods attached at A and D each have a 20-mm diameter and happen to be parallel in the positicn shown. Solve for the average normal stress in (a) member AE, [b) member DG if the applied load at point Cis 800 N. 150 mm G00 m
Question 2 Determine the support reactions for the system shown, given the force P and distributed load w noted below. All dimensions are in millimetres (mm). W B 2400 3000 4000 1000 Question 2 . P- 10 kN W= 5 kN RAY kN (0 decimal places) RET kN (0 decimal plaçes) Rox AKN (0 decimal plaees) Rpy kN (0 decimal places)
The block shown in Figure 2 is subject to three forces. a) Determine the normal voltage at point A. b) Determine the normal voltage at point B. DICE: b = 100mm; b ’= 50mm; d = 75mm; d '= 125mm; P1 = 500N; P2 = 1250N; P3 = 250N. Disregard the weight of the block. Please show me step by step