The air in an ideal Otto engine is initially at 14.5 psia, 100 deg F. At the end of isentropic compression, the pressure is 352 psia; at the end of combustion, the pressure is 1100 psia. Find (a) rk, (b) the percentage clearance, (c) T3, (d) e, and (e) If the sink temp is 100 deg F what percentage of the available part of the heat added was utilized?

Q: ompression ratio of 5. At the beginning of compression the volume is 6ft3 essure is 13.75 psia and…

A:

Q: At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 130 degF. The…

A:

Q: Read the problem carefully and provide complete solutions with derivation of formulas (integrals and…

A: Introduction: The dual cycle combines the Otto and Diesel cycles, it is also known as the restricted…

Q: At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 130°F The…

A:

Q: The air in an ideal Otto engine is initially at 14.5 psia, 100 deg F. At the end of isentropic…

A:

Q: The air standard given in the figure is the pressure ratio 7 of the regenerative Brayton cycle and…

A: Write the given values using suitable variables. Here rP signifies pressure ratio, P1 signifies…

Q: At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 130F. The…

A: A

Q: from the fu

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Read the problem carefully and provide complete solutions with derivation of formulas (integrals and…

A:

Q: 15₁ Q2// The air supplied to a gas turbine plant is 10 kg/s. The pressure ratio is 6 and pressure at…

A: To find: The thermal efficiency of plant. Given: The air supplied to gas turbine is m˙=10 kgsec. The…

Q: no. 3 question: A diesel engine powers a boat. The engine’s cylinders each have a compression ratio…

A:

Q: In an open cycle Gas turbine plant, air enters the compressor at 1 bar and 27° C. The pressure of…

A:

Q: an ideal combustion cycle on 0.65 kg of air. at the beginning of compression, the air is at 100 kpa,…

A: For a step-by-step solution have a look through the attached pictures of the solution. The required…

Q: In a C.I. engine working on the dual combustion cycle the compression ratio is 12.5:1. Air at…

A:

Q: An ideal Otto engine, operating on the hot-air standard with k=1.34, has a compression ratio of 5.…

A:

Q: At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 17 psia and 100F. The…

A:

Q: gas turbine with reheat has a TIT of 1230°C, a compressor pressure ratio of 16, and compressor and…

A:

Q: The Fifth Question: A six-cylinder, 4-stroke petrol engine develops 62 H.P at 3000 r.p.m. The…

A: Given- 6-cylinder,4-stroke 62H.P at 3000rpm ηv=85%ηT=25%Cv=44100Kj/KgAir-fuel ratio = 15:1 To Find;-…

Q: At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 1300F. The…

A:

Q: A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure & temperature…

A: Given that, Velocity of turbojet aircraft, V=790 ft/sec,Pressure orf engine, P1=14.7 psi,Temperature…

Q: an air-standard Carnot cycle heat is transferred to the working fluid at 1100 K, and heat is…

A: To given thatHigher temp.T1=1100Klower temp.T3=300KHeat transfer of working fluid=100kj/kgMinimum…

Q: At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 1300F. The…

A: m˙=.2 lb/secP1=14 psiaT1=130° FMaximum temperature T3=4500°R or T3=4040.330°FCompression ration…

Q: A uniform oil flow enters a pipeline at a flow rate of 0.05 m3 /s. The diameter of the pipeline is…

A: Given data Diameter of pipeline = 15 cm = 0.15 mVolume flow rate = 0.05 m3Density = 890 kg/m3Dynamic…

Q: An ideal diesel cycle powered by air has a compression ratio of 20. At the beginning of the…

A: An ideal diesel engine consists of 4 thermodynamic processes. The four processes involved are 1-2:…

Q: (17 blanks) Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below…

A: Given data Carnot engine , where the cycle goes from ad-ab-bc-cd

Q: In a Diesel cycle, the volume at the end of the isentropic compression is 0.07 L. If the displaced…

A:

Q: PROBLEM: Rd www A regenerative-reheat gas turbine with intercooling between turbine stages is shown…

A:

Q: An ideal Otto engine, operating on the hot-air standard with k = 1.34, has a compression ratio of 5.…

A:

Q: Q2/ Calculate the thermal efficiency of the heat engine working on the diesel cycle takes in air at…

A: P1 = 1 bar  T1 = 20°C = 293 K  r = 12  Tmax = 1100°C = 1373 K  k = cp / cv  = 1.4

Q: An ideal otto engine , operating on the hot air standard with k= 1.3, has a compression ratio of…

A: Given data as per question  k= 1.3  compression ratio = 6  Volume  =0.1982 cm3 = 7 ft3 Initial…

Q: Problems 1. An Otto cycle operates on 0.1 lb/s of air from 13 psia and 130°F at the beginning of…

A:

IC engines

The term "engine" indicates a mechanical device/machine used to convert input energy to a specific mechanical output. The input energy may be in the form of chemical energy, thermal energy, or so on and mechanical output is in the form of mechanical energy (work done). Generally, the engines classify into two groups which are internal combustion type and external combustion type, and further, these two types can be classified into two types that are reciprocating and rotary engines.