15₁ Q2// The air supplied to a gas turbine plant is 10 kg/s. The pressure ratio is 6 and pressure at the inlet to the compressor is l'bar. The compressor is two stages and provided with perfect intercooler. The inlet temperature is 300 K and the maximum temperature is limited to 1073 K. the isentropic efficiency of compressor each stage is 80%. The isentropic efficiency of turbine is 85%. A regenerator is included in plant whose effectiveness is 0.7. Neglect the mass of fuel. Determine the thermal efficiency of the plant. ६ Inter cooler 12:41 Tri Tu с L.P. Air in 0 с H.P. Exhaust Regenerator 3-6 supply Alternator B₁= & Bu

15₁ Q2// The air supplied to a gas turbine plant is 10 kg/s. The pressure ratio is 6 and pressure at the inlet to the compressor is l'bar. The compressor is two stages and provided with perfect intercooler. The inlet temperature is 300 K and the maximum temperature is limited to 1073 K. the isentropic efficiency of compressor each stage is 80%. The isentropic efficiency of turbine is 85%. A regenerator is included in plant whose effectiveness is 0.7. Neglect the mass of fuel. Determine the thermal efficiency of the plant. ६ Inter cooler 12:41 Tri Tu с L.P. Air in 0 с H.P. Exhaust Regenerator 3-6 supply Alternator B₁= & Bu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QI/Calculate the power in kilowatts of the gas turbine power plant has a greatest temperature of 700°C and a pressure ratio of 10. The isentropic efficiencies of the turbine and compressor are 0.85 and 0.82 respectively. The mass flow rate of the air that inlet to the compressor is 15 kg/s at 15 °C. At the expansion process take Cp= 1.11 kJ/kg:K, y=1.333, and at the compression process take c,= 1.005 kJ/kg K, and y =1.4
An ideal diesel cycle powered by air has a compression ratio of 20. At the beginning of the compression process, the pressure of the air is 100 kPa, the temperature is 20 °C and the highest temperature of the cycle must not exceed 2250 K. Show the cycle in the P-v diagram.Then calculate: a) The heat entering and leaving the cycle, the thermal efficiency of the cycle, b) the average effective pressure of the cycle. Assume that specific heat is constant at room temperature constant at temperature. k=1.4 CP=1.005 kJ/kgK CV=0.718 kJ/kgK R=0.287 kJ/kgK
the compression ratio of an ideal Otto cycle is 8. Pressure of air at the beginning of the isentropic compression process 95 kPa, Temperature 27 °C and constant volume input to the cycle is 750 kJ / kg. Consider that the specific constant is taking; which of the following are the temperature and pressure values at the end of the heat input into the cycle? (Cp=1.005 kJ/ups, C, =0.718 kJ / ups, R=0.287 kJ/ups, k=1.4) Please select one: a.4392 КРа 1534к O b.4392 Pa 1534 K с. 439.2 КРа 1734 К d.439.2 kPa 1534 K e.4392 kPa 1734 K
S4
Q1/ A gas turbine operates with components as shown in figure 1. Air enters this first compressor at 96.5 kPa. and 15.5°C; the pressure ratio is 3 for each stage of compression; the air temperature when entering a turbine is 504.5°C; and the heat perfect exchanger. (Take air index as 1.4 and specific heat as 1.005 kJ/kg.K). Draw T-S diagram and determine: a. The air mass flow rate, and the rates of heat addition and rejection when this produced power is 745.7 kW. b. What will be the effect of using normal heat exchanger on the thermal efficiency? Inter-cooler c2 Cormpressors Turbines Generator set cc 1 State1 Нeat Exchanger State10
An iseal Brayton cycle has a pressure ratio of 6:1. The temperature of the air is 22 degrees celsius at the inlet to the compressor and 1080 derees celsius at the inlet to the turbine. Take specific heat at constant pressure and constant volume for air as 1,006 KJ/kg K and 0,717 KJ/kg K respectively. Calculate: 1. the compresion absolute temperature to one decimal place 2. the work ratio of the plant to three decimal places 3. the specific work output to the turbine and specific work input to the compressor , to one decimal place and SI unit 4. the thermal efficiency of the plant to one decimal place
A Brayton cycle with an air-powered regenerator has a pressure ratio of 8. The lowest and highest temperatures of the cycle are 310 K and 1150 K. The adiabatic efficiencies of the compressor and turbine are 75% and 82%, respectively, and the efficiency of the regenerator is 65%. Show the cycle in the T-s diagram. Consider the variation of the specific heats with temperature. a) The temperature of the air at the turbine exit, b) Net work of the cycle, c) Calculate the thermal efficiency of the cycle.
A single-acting two-stage air compressor deals with 4 m³/min of air at 1.013 bar and 15°C with a speed of 250 rpm. The delivery pressure is 80 bar. Assuming complete intercooling, find the minimum power required by the compressor and the bore and stroke of the compressor. Assume a piston speed of 3 m/s, mechanical efficiency of 75% and volumetric efficiency of 80% per stage. Assume the polytropic index of compression in both the stages to be n = 1.25 and neglect clearance.
None