Consider a Brayton Cycle with all the goodies installed: Regenerator (c=75%); Intercooling of 2-Stage Compressor (nc = 85%); and Reheating for 2-Stage Turbine (nr = 80%). The pressure ratio rp = 10:1, with air entering the compressor at 100 kPa and 300K. Maximum Temperature is set to 1500K. Pressure ratios will be equal in the Compressor and Turbine. a) Draw the Schematic with state point labels. b) Populate the table below. State Temp [K] Enthalpy [kJ/kg] 1 300 K 2s 2a 3 4s 4a 5 6 7s 7a 8 9s 9a 10 300 K 1500K

Consider a Brayton Cycle with all the goodies installed: Regenerator (c=75%); Intercooling of 2-Stage Compressor (nc = 85%); and Reheating for 2-Stage Turbine (nr = 80%). The pressure ratio rp = 10:1, with air entering the compressor at 100 kPa and 300K. Maximum Temperature is set to 1500K. Pressure ratios will be equal in the Compressor and Turbine. a) Draw the Schematic with state point labels. b) Populate the table below. State Temp [K] Enthalpy [kJ/kg] 1 300 K 2s 2a 3 4s 4a 5 6 7s 7a 8 9s 9a 10 300 K 1500K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Brayton cycle inlet is at 300 K. Inlet and exit temperatures of the turbine is measured as 1800 K and 710 K, respectively. The compressor pressure ratio is 13. Use cold air-standard approach to calculate the thermal efficiency of the cycle. BURNER- COMPR. TURBINE a. 0.35 O b. 0.40 C. 0.45 d. 0.50 e. 0.55 f. 0.60 g. 0.65 Seçimimi temizle
Explain ideal Rankine cycle with P-V, T-S and h-S plot.
Question #1 (10 pts) Rankine cycle – Consider the ideal cycle shown below and determine the thermal efficiency of the cycle using the steam tables. T 500 °C 3 Wturb,out Tin 6 MPа 10 kPa Jout pump,in
Air temperature 30 ° C pressure 1 bar flows into the ideal gas turbine cycle by a pressure ratio air compressor (r). 12 The hot gas discharge temperature from the combustion chamber is 1200 K. The air flow in a constant cycle is 60 kg/s a. Draw the diagram T-5 of this cycle b. Find the net power output (kW). C. Find the thermal efficiency of this cycle
In a Brayton Cycle air enters the compressor at 101.32 kPa, 32 °C and leaves at a pressure of 808 kPaa. The air is heated to 717 °C in the combustor. For a net output of 2125 kW, compute: a) mass flow rate of air (kg/s), b) thermal efficiency of the cycle. use k = 1.4 for all problems
What are the difference between jet cycle and open Brayton cycle.
True or False 1) In a Rankine Cycle, real work produced by the turbine is less that the isentropic work. 2) A valve (throttling) and ideal pump both operate isenthalpically 3)For a given TC and TH, the vapor compression cycle has a higher COP than the Carnot cycle. Group of answer choices
(b) Derive an expression for thermal efficiency of ideal Brayton cycle
A spark – ignition engine has a compression ratio of 8.5 and a maximum temperature of 945.15K. At the beginning of compression stroke, P and T of the fluid are 0.1 MPa and 28.65 deg C. Assuming hot air-standard analysis, how much work (kJ/lb) is produced per cycle completion?
A The compression ratio of a diesel cycle is 15.5, and the cutoff occurs at 10% of the stroke.14 psia and 600 K characterize state 1. Calculate the following for the hot-air standard with k= 1.34and a starting volume of 2 cu ft:a. Find T2 , P2 , V2 , T3 , V3 , P4 , and T4b. Compute the heat added (QA),heat rejected (QR), work (W) andthe cycle efficiency (e).c. for a rate of circulation of 1000 cfm,compute the horsepower.
A The compression ratio of a diesel cycle is 15.5, and the cutoff occurs at 10% of the stroke. 14 psia and 600 K characterize state 1. Calculate the following for the hot-air standard with k= 1.34 and a starting volume of 2 cu ft:a. Find T2 , P2 , V2 , T3 , V3 , P4 , and T4b. Compute the heat added (QA), heat rejected (QR), work (W) and the cycle efficiency (e).c. for a rate of circulation of 1000 cfm, compute the horsepower
A The compression ratio of a diesel cycle is 15.5, and the cutoff occurs at 10% of the stroke. 14 psia and 600 K characterize state 1. Calculate the following for the hot-air standard with k= 1.34 and a starting volume of 2 cu ft: Qin a. Find T2 , P2 , V2 , T3 , V3 , P4 , and T4 3 P = P, b. Compute the heat added (QA), Wout heat rejected (Qr), work (W) and the cycle efficiency (e). P. c. for a rate of circulation of 1000 cfm, Qout compute the horsepower.