Another name of driving-point admittance is O Self admittance O Mutual admittance O Leakage admittance O Transfer admittance Another name of Swing bus is O PV bus O PQ bus O Slack bus O Generator bus

Q: Q2) Explain using diagram and equations the generation of AM DSB/LC using non-linearity.

A:

Q: Quèstion 6 NPN BJT is considered as two diodes their anodes are connected together. True False

A: In this question let us consider what is a transistor and how it can be realized using a 2 diode…

Q: Ic(sat) + IC Icq 0 .a Vceq Vce(cut-off) VCE RB W +VCC C E RC B=100 RE

A:

Q: Draw FWR Vs=15Vrms Vrpp=.2v VDC=? R=5000hm F=60HZ C=?

A: Given, Vrms=15VRL=500ΩVrpp=0.2VSo,Vrrms=Vrpp2=0.22V,Vrrms=Vpp2⇒Vpp=2 VrmsSo, VDC=2Vppπ=22 Vrmsπ…

Q: What does matched load mean?What happens if the load is not matched?

A: In this question, we will define matched load..

Q: Q23. Using the below circuit draw the following waveforms over the period of 4 m if the firi angle…

A: Given thyristor firing angle π which is 180° since thyristor works for postive half cycle with gate…

Q: What is the use of finding phase margin? How will you determine stability using phase margin?

A: we need to know What is the use of finding phase margin? Usefulness of finding phase margin: phase…

Q: For given circuit below Adjuts the VGG voltage to have following Vas values and calculate the…

A: Given circuit is shown below. Given data is VDD=12V, RD=1kΩ, RG=560kΩ. For MOSFET input current is…

Q: Project # 2: Give the following AC circuit (take note that L1 & R2 are in series but parallel with…

A:

Q: (7) Determine Is,Ic,IE, VB,and Vc in the following figure, where Bpc is 48. ww Rc >1.2KQ Vac 14.

A: Circuit diagram is given as,

Q: A load voltage with flicker can be represented by the following equation Vload =…

A:

Q: For a type-1 system with input ramp signal, the value of steady state error is 0.23.  The value of…

A:

Q: Q8. What is the difference between Zener breakdown and Avalanche breakdown?

A: The main difference between Zener breakdown and avalanche breakdown?

Q: 9. Given zener voltage at 9V, input voltage at 12Vdc to 15Vdc and ILmax at 40mA. What is Rsmin if…

A: As per the guidelines given to us, we can only solve the only one question in multiple type of…

Q: Ps Two Conductonces G ard. G2 having Valnes of bao and. Joo rS respectiny The Combination is then…

A:

Q: Impulse flashover test is conducted to know the characteristics of insulators and lightning…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: For the given BJT circuit, determine the operating point and plot the DC load line showing the…

A: In this question, we need to determine the operating point of BJT and DC load line.We know Voltage…

Q: 11- The main three common types of photovoltaic cells are a.

A: Since you posted the multiple questions, therefore we will solve questions 11 for you.

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: For a system if the value of peak overshoot is 26 %,  then the value of damping ratio  is .......

A:

Q: Determine the branch currents I₁, Igandl, in ampere. 50 1012 10 V al. The current in ampere 11…

A: We need to find out the current for given circuit by nodal analysis .

Q: 11. i)Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in…

A: given data:

Q: he condition of the power system gives the power flow solutions when the transient behavior of the…

A: The explanation is as follows.

Q: 91 kQ 18 ΚΩ • 330 ΚΩ VOSQ 1.1 k Vc 0-100 Vo LOSS V=-OV le E o 20 V 100 1.2 kQ

A:

Q: FACTS: AC-DC converters take the AC power from wall outlets and convert it to unregulated DC. These…

A: The solution is given below

Q: P3 Two Conductancas G ard G2 haring valnes of b00 ard. Joo s respectinl, are connectid in pavallil.…

A:

Q: a(t) +

A:

Q: nse. Quèstion 8 NPN BJT is considered as two diodes their anodes are connected together. True False

A:

Q: 6. The discharge curves shown are typical of which components? (a) Capacitors (b) Inductors (c)…

A: The type of device which exhibits the given graph needs to be identified. Two different plots are…

Q: 1. Why sub transient current magnitude is large compare to steady state current?

A: In power system transient and sub transient current it is occur only when three phase fault occur in…

Q: C = 93 | F = 14 | G = 39 | S = 85 For the sinewave, give the following six values. Must give the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: The minimal cut sets for a series system is always a lower bound on Reliability. True False The…

A: The minimal cut sets for a series system is always a lower bound on Reliability. True False The…

Q: 6) Calculate the total resistance and the current flowing through the circuit when the voltage is…

A:

Q: Q2. A small industrial user was fed from a 500 kVA, 11 kV/433 V transformer with a leakage impedance…

A:

Q: Write a conclusion to the measured values from the 3 different rectifier circuit.

A: Rectifier: It is an electronic circuit which converts AC voltage  to pulsating DC voltage . Half…

Q: discuss about UNIT COMMITMENT process.

A: Unit Commitment means to Turn a generator ON and to bring it to synchronized speed with other…

Q: The AC and DC power of the rectifier circuit are 328 Watts and 285 Watts respectively. The…

A:

Q: make me Complex Example of pls. dn Power

A: Complex power is the sum of real and reactive power. The unit of complex power is KVAR (volt-ampere…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.