Analyze the various properties of materials, testing, machining and production equipment for manufacturing] a. What quality character/parameters are required from your design above, state some of these characters and qualities in monitoring the quality of the product b. Describe what deviations could occur from the process that could cause out of specification 3. Uses instruments and measuring based on a quality assurance method For no.2a: what measurement method and tools should be used

Analyze the various properties of materials, testing, machining and production equipment for manufacturing] a. What quality character/parameters are required from your design above, state some of these characters and qualities in monitoring the quality of the product b. Describe what deviations could occur from the process that could cause out of specification 3. Uses instruments and measuring based on a quality assurance method For no.2a: what measurement method and tools should be used

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.5: Quality Assurance, Process Planning, And Quality Control

Problem 2RQ: Briefly define quality control and explain its purpose.

See similar textbooks

Similar questions

During the development of a product, an entirely new process plan is made based on design logic, examination of geometry and tolerance information. This type of process planning is known as A. retrieval B. generative C. variant D. group technology based
In the context of our teaching, which one of the below statements is mostly correct about in detailed design of a component? In the reporting, I do not need to include the reasoning for my design decision for a good quality report. I cannot use appendix, so I am struck with the word limit for reporting. For a good clarity, I should not explicitly report what are the key dimensions and their tolerances in the drawing and in the body of text. The word count limit for detailed design report is 160O.
hand written plz 6. Design for , that is, the load can be taken by other members or the effect of fatigue failure otherwise mitigated, until the failed component can be detected and repaired or replaced. This approach is common in aircraft structural design. 7. create variations in dimensions, which can affect wear and fatigue properties. 8. is often used as the starting point to identify the most important problems and the most likely causes. 9. is a type of failure mode identification test, which use one/two samples to establish multiple design inherent failure modes, and establish operating and destruct limits of a product. 10. concerns the improvement in reliability, during use, that comes from field data feedback resulting in modifications.
What process is used to verify that a manufactured part or hardware component conforms/follows the intent of the design and customer specification? HINT: The answer is one word - not an acronym.
Question 2 1. What is a First Article Inspection and why it is needed? Explain briefly (with the help of the following drawing)the steps that you take to prepare FAI in terms of design, manufacturing, and inspection of any part First Article Inspection Requirements RAW MATERIAL DRAWINGS, STANDARDS, SPEC SHEETS SPECIAL PROCESSING REQUIREMENTS TEST SPECIFICATIONS PROCEDURES SPECIAL PROCESSES (ANODIZATION, CLEANING ETC,). RAW CONVERSION FUNCTIONAL MATERIALS PROCESSES (MACHINING, CASTING ETC.) TESTING (AL6061 T6, 301SST etc.) CERTIFICATE OF CONFORMANCE TEST CERTIFICATE OF CONFORMANCE DIMENSIONAL MEASUREMENTS RESULTS MANUFACTURING ENGINEERING
4. Describe the dimensions: design quality and conformance quality.
In a certain manufacturing company, the motorcycles are produced in a single assembly line with 25 different stations. Upon Quality Assurance inspection of produced motorcycles, the production stopped because it was found out that station 22 was not able to put the necessary part. What type of inspection is represented by the scenario? Post-Process In-Process
ASSIGNMENT 1 1 What is product life cycle? State the stages involved in product life product. Why is it important to integrate reliability engineering into product life cycle? Describe the key engineering tasks and reliability roles in each phase of a product life cycle. Explain the important difference between serial and concurrent product realization processes. How should a reliability program be organized in the environment of concurrent engineering?
A customer has recently tightened the specs for a part your company supplies. The specs are nowmuch tighter than the machine being used for the job is capable of. Briefly identify alternativesyou might consider to resolve this problem.
In the case that the average measure of quality equals the target, the equation for the process capability ratio is: |USL – LSL| Cp = бо A company's customers need the product to have a quality measure between 2 and 6. The company provides the product with a quality measure having a standard deviation of 1.0. What is the process capability ratio?
This is Engineering Data Analysis
OM A customer has recently tightened the specs for a part your company supplies. The specs are now much tighter than the machine being used for the job is capable of. Briefly identify alternatives you might consider to resolve this problem.