Analyze the given program in which the value stored in 1000H is ABH. (i) Write the values of the registers after the execution of each instruction. (ii) Find the value stored in the memory location 41H after the execution of the program. (iii)What will be the status of flag bits of PSW after executing the program by changing the value of R4 from 100 to 75?

Analyze the given program in which the value stored in 1000H is ABH. (i) Write the values of the registers after the execution of each instruction. (ii) Find the value stored in the memory location 41H after the execution of the program. (iii)What will be the status of flag bits of PSW after executing the program by changing the value of R4 from 100 to 75?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Which of the following statements is correct? 1) The 80/20 rule asserts that 80% of the instructions are executed and 20% of the instructions are produced. 2) The external bus in von Neumann architecture is exclusively used for data memory.
2. Study this program then answer the questions that follow: MOV DX, 1234 H MOV BX, 3099 H MOV AL , BL ADD AL , DL DAA MOV CL , AL MOV AL , ВН ADC AL , DH DAA MOV CH ,AL HLT • What the operation is performed by this program ? • What is the result produced by Execute each instruction ? • Why we use the ADC instruction ? Why we split the contents in BX to (BH & BL) and in DX to (DH & DL ) before added, can add these numbers directly ?
Fill in the following table showing the results of the indicated instructions, using the register values shown. Also, show the OF and CF values AFTER the instruction executes. Show all results in hexadecimal. Show OF and CF as 0 or 1.
Given the binary format of an instruction as follows0000 0011 0000 1000 1000 1000 0110 0011a. What assembly instruction does this correspond to?b. If the PC = 0X0040 00F4, what is the target address?c. How many instructions forwards or backwards is that?d. How many bytes is that in decimal?
Suppose the opcode of an MIPS instruction is 8 in decimal, and the rest of the machine code is 309FC88 in hexadecimal (from high-order bit to low-order bit). What is the instruction? When showing the registers, use names (e.g. $t0, $s2) instead of indices (e.g $8, $17). For branch instructions, show offset in place of label, e.g. beq $t1, $t2, 92. Answer:
For the RISC-V assembly instructions below, what is the corresponding C statement? Assume that the variables f, g, h, i, and j are assigned to registers x5, x6, x7, x28, and x29, respectively. Assume that the base address of the arrays A and B are in registers x10 and x11, respectively. sub x30, x28, x29 slli x30, x30, 2 add x3, x30, x10 add x4, x30, x11 1w x30, 0 (x3) 1w x31, 0 (x4) add x30, x30, x31 sw x30, 16 (x11)
Urgent
The stack segment, data segment, and code segment are all separate entities. Next, ascertain which combination of registers is used to address data items inside each segment.
What are the contents of flag register () after the executing the following sequence of instructions? MOV AL, 01011000B MOV BL, 33H CMP AL, BL Assume that flags Z, S, C, A, O, and P are all initially reset. Your answer