An wants Engineer to convert a tied rectangular column to a spiral column having H=500mm and b=300mm, f'c = 21Mpa and fy= 276Mpa. The Column is reinforced with 6-25mm deformed bar. Determine the Diameter of the of spiral column. assume concrete cover is 40mm and diameter of stirrups = 10mm. Use exact value in millimeter and 3 decimal places.

An wants Engineer to convert a tied rectangular column to a spiral column having H=500mm and b=300mm, f'c = 21Mpa and fy= 276Mpa. The Column is reinforced with 6-25mm deformed bar. Determine the Diameter of the of spiral column. assume concrete cover is 40mm and diameter of stirrups = 10mm. Use exact value in millimeter and 3 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the minimum area (Asmin) for the following concrete beam: b = 10 in, d = 17 in, fy = 60000 psi, and f'c = 5000 psiNote: This is an ACI code check and not required As determined by the moment. Answer in inches^2 and to 3 decimal places. Type your answer...
Find the safest value of load "P" for the beam loaded shown. fc'=35MPA, Use GRADE 420 steel bar and n=10 The answer is kN. Assume unit weight of concrete = 24kn/cu.m. 200 3 m 1 m toort twit 3P 70 200 2-20 mm O 330 3. BEAM 4-32 mm Ø 300 100 DIMENSIONS ARE IN "mm"
Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
Principle of Reinforced Concrete Design
The following is a cross-section of a tied column reinforced with 16-32 mmø. Using fc' = 28 MPa and fy = 415 MPa. Size of aggregates used is 25 mm. O Computè the safe ultimate load that the column could carry. ® Compute the spacing of the 10 mm wires. 3 . Compute the min. clear cover over the tie wire. O Compute the clear spacing between longitudinal bars. -600 600
1/ Calculate maximum deflection of the beams (This was solve it) 2/ Check the suitability of the section assuming the code limitation of L/240. 3/ If maximum deflection doesn’t meet the code requirement, propose your solution
Plz
ASAP dont round off initial values, round off final ans only
A circular Column has dia of D 30 in. Concrete Compressive strength at 28 days is of steel is (60 + 60) ksi. Determine the design capacity of circular column and 8 # 11 bars is used. (4 + 60) ksi and yielding strength
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
Problem No. 3 A beam 200x45Omm is reinforced by 2-32mm diameter rebar. Assume cc=50mm, stirrups=10mm, fc'=21Mpa and fy=415Mpa. Calculate the following. 17. Calculate the strain of the steel reinforcement 0.00182 O 0.00201 O 0.00224 0.00391 O 0.00577