An uncontrolled 1050 kg car strikes squarely a motorway crash cushion in which the car is brought to rest by successively crushing steel barrels. The length of the crash cushion is 6.1 m, and the magnitude F of the force required to crush the barrels as a function of the distance x the car has moved into the cushion is given by (0 < x < 1.7m) (1.7 < x < 4.7m) 80KN 110kN 155kN (4.7 < x < 6.1m) a) Determine an expression for the work done by the force F as a function of x. b) If the car strikes the crash cushion with a velocity of 119 km/h, determine the distance the car will move into the cushion before it comes to rest and the maximum deceleration of the car. c) Determine the maximum velocity with which the car can strike the cushion so that it will not hit the wall behind the cushion.

An uncontrolled 1050 kg car strikes squarely a motorway crash cushion in which the car is brought to rest by successively crushing steel barrels. The length of the crash cushion is 6.1 m, and the magnitude F of the force required to crush the barrels as a function of the distance x the car has moved into the cushion is given by (0 < x < 1.7m) (1.7 < x < 4.7m) 80KN 110kN 155kN (4.7 < x < 6.1m) a) Determine an expression for the work done by the force F as a function of x. b) If the car strikes the crash cushion with a velocity of 119 km/h, determine the distance the car will move into the cushion before it comes to rest and the maximum deceleration of the car. c) Determine the maximum velocity with which the car can strike the cushion so that it will not hit the wall behind the cushion.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I have three parts that I need answered pertaining to the print provided below. What material is specified for this part? (Multiple Choice)a. Cold Drawn Steel CD1040b. Hot Rolled Steelc. Delrin #360d. Brass FM#360 What size paper was used for the original version of this print? (Multiple Choice)ABCD The two views near the bottom of the print are called detail views. Which one of theviews above (left side, front, or right side) shows the same geometry, but at the normal 1:1scale? (Multiple Choice)a. left sideb. frontc. right side
Complete the following table for the sample that your group tested in the laboratory: Load (kg) Extension (AL) Stress (F/AInitinl) Strain (AL/L) 962.2 1.4387 12.45 0.018 2015.2 2.4713 27 0.031 2182.4 3.4800 29.33 0.044 2416.9 4.9900 32.48 0.063 2693.1 7.5062 36.19 0.095 2827.7 10.0325 38 0.127 2921.5 15.0637 39.26 0.191 Plot the stress-strain diagram for your specimen material, and indicate the 0.2 % yield stress, ultimate tensile strength, the % elongation, % reduction in area, modulus of elasticity,. Use ordinary millimeter graph paper. After finishing answer the following questions. 1. Calculate the values of % elongation and % reduction in area and indicate their significance? 2. Calculate the elastic modulus using the slope of the linear portion of the curve. 3. Determine the 0.2 % yield stress. 4. What property does the area under the stress-strain define? 5. Compare the stress-strain curves for the cold-rolled and annealed steel and the aluminum specimens shown hereunder, your…
please, i need to see how did you get to this formula
I need problems 7, 8, and 9 answered pertaining to the print attached below.
I have three parts that I need answered pertaining to the print provided below. For this print, of what significance is the number 81073? (Multiple Choice) a. It is a paint code used for military specification b. It is a part number used for backorder situations c. It has no significance to most sub-contractors d. It is a CAGE (commercial and government entity) code number for governmentcontracts. This part features some concave arcs that are equally spaced. There are some larger arcs (.072 radius) spaced _____ degrees apart and some smaller arcs (.030 radius) spaced _____degrees apart. (Multiple Choice)a. 22.5 (22°30′); 22.5 (22°30′)b. 12.5 (12°30′); 11.25 (11°15′)c. 20.5 (20°30′); 10.25 (10°15′)d. 22.5 (22°30′); 11.25 (11°15′) What type of section is shown in Section B? (Multiple Choice)a. Offsetb. Fullc. Halfd. revolved
I need help answering this Review Activity
Interpret the significance of the letters shown in the illustration (A through F)
part 1 and 2 please
Give 1 example of methods of section
Question 1 An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is 3 mm thick in SOLIDWORKS. The engineer most likely used the feature. Chamfer Fillet Hole Extrude
You are a mechanical engineer tasked with overseeing the equipment used in constructing a high-rise. A tower crane, used to lift and move heavy construction loads, is being used in the construction site.
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857