An oil of specific gravity 0.78 is flowing through the pipe of diameter 30cm. one end of the simple U tube manometer which contains mercury, is inserted with the center of pipe and other end is open to atmosphere. The level difference in mercury is found in the right limb as 36 cm. The distance between the center of the pipe and the mercury level in right limb is 12 cm. Find the pressure of oil in the pipe in kPa.

An oil of specific gravity 0.78 is flowing through the pipe of diameter 30cm. one end of the simple U tube manometer which contains mercury, is inserted with the center of pipe and other end is open to atmosphere. The level difference in mercury is found in the right limb as 36 cm. The distance between the center of the pipe and the mercury level in right limb is 12 cm. Find the pressure of oil in the pipe in kPa.

Name: 42 ll lkAn oil of specific gravity 0.78 is flowing throughthe pipe of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 42 ll lkAn oil of specific gravity 0.78 is flowing throughthe pipe of diameter 30cm. one end of the simpleU tube manometer which contains mercury, isinserted with the center of pipe and other end isopen to atmosphere. The level difference inmercury

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump discharges 8000 liters per minute of a certain brine solution (SG=1.20) to an evaporating pond. The intake line is 25cm in diameter and is at the same level as the pump discharge line, which is 15cm in diameter. The pressure at the inlet of the pump is -170mm of mercury. The pressure gage connected to the pipe discharge reads 150 kPa, and its center is 2.0mabove the center of the discharge flange. The vapor pressure of the brine solution is 40mm of Hg. If the pump efficiency is 80%. How much power is required?
A vertical, clean, glass piezometer tube has an insidediameter of 1 mm. When pressure is applied, water at20 ° C rises into the tube to a height of 25 cm. After correctingfor surface tension, estimate the applied pressurein Pa.
Two small vessels are connected to a U-tube manometercontaining mercury(relative density 13.56) and the connectingtubes are filled with alcohol (relative density 0.82). Thevessel at the higher pressure is 2 m lower in elevation than theother. What is the pressure difference between the vessels whenthe steady difference in level of themercury menisci is 225 mm?What is the difference of piezometric head? If an inverted U-tubemanometer containing a liquid of relative density 0.74 wereused instead, whatwould be the manometer reading for thesame pressure difference?
Fast plz
The figure below shows a rectangular tank of dimensions ho = 2.5 m and b = 2 m is filled to the brim with a liquid of specific gravity 1.1 (tank is 1 m into plane of figure). The tank is subjected to a horizontal acceleration ax, and 30% of the liquid spills over. Determine the difference in liquid pressures at the lower left-hand corner (Point E) and lower right-hand corner of the tank (Point F). PE-PF= 1. [15.70090597, 16.672095597 Free surface ho Liquid X b Liquid at rest ➡ho kPa. 9 Free surface Liquid b ax Under constant acceleration
Some manometers are constructed as in Fig. , whereone side is a large reservoir (diameter D ) and the other sideis a small tube of diameter d , open to the atmosphere. Insuch a case, the height of manometer liquid on the reservoirside does not change appreciably. This has the advantagethat only one height needs to be measured rather than two.The manometer liquid has density ρ m while the air has densityρ a . Ignore the effects of surface tension. When there isno pressure difference across the manometer, the elevationson both sides are the same, as indicated by the dashedline. Height h is measured from the zero pressure level asshown. ( a ) When a high pressure is applied to the left side,the manometer liquid in the large reservoir goes down,while that in the tube at the right goes up to conserve mass.Write an exact expression for p 1gage , taking into account themovement of the surface of the reservoir. Your equationshould give p 1gage as a function of h , ρ m , and the…
The pipe (0-1-2) shown in the …gure is angled upward at 30 and is …lled with water. The distance from (1) to (2) (along the pipe) is 1.2 m. The manometer liquid is mercury. For part (a), the pipe is capped at location (0) so that the water is stationary in the pipe. What would be the value of h in this case? For part (b), the pipe shown is just a section of a much longer pipe, and water is ‡owing upwards from (0) to (1) to (2). If the pressure loss due to friction from location (1) to location(2) is 20 kPa, what is the value of h in this case?
I need the answer as soon as possible
2. A vertical cylindrical tank is filled to the top with water at a temperature of 20°C. The diameter of the tank is 12m and depth of 4m. If the water is heated to 50°C, how much water will spill over in m? 3 A quart of SAE 30 oil at 6goE weighse about 1 85lh. Calculate the oil's
2. The tank shown contains alcohol (SG=D0.78) and covered by a circular plug 1.2 m in diameter. Calculate the hydrostatic force F Am acting on the plug and its center of pressure. 8m 1.2 m 3. The gate as shown is 3 m normal to the page. It keeps the two liquids from mixing with each onough clocuro botween the oil and
(1) The mercury manometer in the Figure below is connected to the inlet and outlet of a water pump (the left side to the inlet and the right side to the outlet). Assuming that the inlet and outlet are at the same elevation, determine the pressure increase for the pump. Inlet and outlet clevation Water hy =15 cm Mercury 13.9 keiul. Density of mercury = 13.6 g/cm3 = 13,593 kg/m3 Density of water = 1.0 g/cm3 = 1,000 kg/m3
Solve Below