An oil engine working on a dual combustion cycle, has a compression ratio of 16: 1 and the cut-off takes place at 6% of the stroke. The maximum pressure obtained is 70 bar. The pressure and temperature at the beginning of compression are 1 bar and 110°C respectively. Determine the pressure and teperature at all the important points of the cycle. Assume R = 0.287 kJ/(kg K) and c, = (0.716+ 125 x 10-67) kJ/(kg K)

An oil engine working on a dual combustion cycle, has a compression ratio of 16: 1 and the cut-off takes place at 6% of the stroke. The maximum pressure obtained is 70 bar. The pressure and temperature at the beginning of compression are 1 bar and 110°C respectively. Determine the pressure and teperature at all the important points of the cycle. Assume R = 0.287 kJ/(kg K) and c, = (0.716+ 125 x 10-67) kJ/(kg K)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

24A petrol engine working on the constant volume cycle has a compressioni ratio of 9 to 1. If the pressure and temperature of the petrol-vapor air mixture at the beginning of compression are 99.30 kPa and 38 C respectively. Calculate the temperature at the end of compression assuming it follows the law PV = C. A 383.45 C B. 728.45°C C. 899.30°C D. 883.48°C
A spark ignition engine of a compression ratio of 8 , operates with stoichiometric fuel-air ratio of hydrocarbon fuel of C8H18. The pressure and temperature inside the cylinder at the start of compression are 1 atmosphere and 350 K respectively. Find the temperature and pressure per unit mass of air at the end of compression stroke. Also find the maximum temperature and pressure in the cycle assuming residual gas fraction is 0.08 and the exhaust temperature is 1800 K. ( note LCV= 44300 kJ/kg and Cpf = 1.979 kJ/kg.K .
In the ideal diesel cycle, the compression ratio is 19 and the shear rate is 2.4. The pressure of the air is 100 kPa at the beginning of the compression process, and the temperature is 420 °C at the end of the compression. If the highest temperature in the system is 1200 K and the specific heat change is considered constant, determine the heat given to the system. (Cp=1,005 kJ/kgK)
4. An engine operating on the air standard heat engine has a heat rejection at constant volume rate of 525 KJ/kg of air used. The minimum pressure and temperature are 98 Kpa and 339 K, respectively. If the bore and stroke of 75mm x 82mm, with cycle efficiency of 56% under heat addition, according to PV^= C wheren = 0. Determine The maximum temperature and pressure • The amount of air used • The work for the cycle %3D
14 A six-cylinder SI engine with a compression ratio of 10.5:1 operates on a four-stroke cycle at 3000 RPM. Air enters the cylinders at T = 110 F and P 12.8 psia. The intake valve closes at 20° aBDC and combustion starts when the spark plug fires at 15° 6TDC. Con- necting rod length is 6.64 in. and crank offset is 1.66 in. Calculate: (a) Cylinder temperature at start of combustion using air-standard Otto cyde analysis ['F] (b) Cylinder temperature when spark plug fires assuming compression doesn't start until intake valve closes. [F]
During a compression stroke of a cylinder in a diesel engine, the air pressure in the cylinder increases from 1.0×10^5 N/m^2 to 50×10^5 N/m^2, and the temperature increases from 26 ∘C to 517 ∘C. Determine the compression ratio for this engine. V2/V1 =?
The displacement volume of an internal combustion engine is 2.15 liters. The processes within each cylinder of the engine are modeled as an air-standard Diesel cycle with a cutoff ratio of 2.5. The state of the air at the beginning of compression is fixed by p1 = 1.6 bar, T1 = 325 K and V1 = 2.36 liters. If the cycle is executed 2100 times per min, determine: a) the compression ratio,b) the net work per cycle, in kJ,c) the maximum temperature, in K,
The displacement volume of an internal combustion engine is 2.17 liters. The processes within each cylinder of the engine are modeled as an air-standard Diesel cycle with a cutoff ratio of 2.5. The state of the air at the beginning of compression is fixed by p1 = 1.6 bar, T1 = 325 K and V1 = 2.36 liters. If the cycle is executed 2100 times per min, determine: a) the compression ratio,b) the net work per cycle, in kJ,c) the maximum temperature, in K,d) the power developed by the engine, in kW,e) and the thermal efficiency.
. Exercise 2 Compute the efficiency of the cycle shown in the figure below, under the assumption that the fluid used is an ideal diatomic gas. The A → B transformation is isothermal, the B →C transformation is isochoric and the C→ A transformation is adiabatic. The compression ratio VB/VA = 3. B V
The displacement volume of an internal combustion engine is 2.15 liters. The processes within each cylinder of the engine are modeled as an air-standard Diesel cycle with a cutoff ratio of 2.5. The state of the air at the beginning of compression is fixed by p1 = 1.6 bar, T1 = 325 K and V1 = 2.36 liters. If the cycle is executed 2100 times per min, determine:d) the power developed by the engine, in kW,e) and the thermal efficiency.