An l-beam is used to supporta distributed live load 11 KN/m and a concentrated live load of 98 KN. The steel beam has a cross sectional area of 37,845 mm. Determine the maximum positive reaction at A. Use steel unit weight of 78.5 KN/m. Beam is pinned at point A and has a roller support at point B. 10m 10m 10m 5m A

Q: 1. The figure below shows a sample loop traverse with the unadjusted field data. For letters a, b,…

A:

Q: Result II. Construct the bending moment diagram of the following structure. Reviewer 8kN 6kN/m A 2m…

A: The algebraic sum of the vertical forces at any section of a beam to the right or left of the…

Q: A five-sided closed traverse was surveyed over the stations ABCDE. At each station, the back bearing…

A:

Q: A cantilever beam has a span of 4.4 m. The beam carries a uniform service dead load w = 24.49 kN/m…

A:

Q: The length of the chord is 325 m long, measured from the P.C. to the P.T. of the curve a common…

A: Given:-azimuth =254.240,270.01o,279.960L=325mazimuth =270.010stationing of PT=6+530To find:-a)total…

Q: Problem: Compute the bar forces of all the members. 35 kN D IT 2.5 m 50 kN ESm 100 kN 5m +5 m 5m

A: Given:- To Determine Force in each member of the truss.

Q: Tests a 14.62-in-diameter centrifugal water pump at 2134 r/min yield the following data: Q, ft’/s 4…

A: To determine the specific speed we have to first determine the best efficiency point. For the best…

Q: 3. Use double integration method to determine the deflection and slope at point C. Given E= 200 GPa,…

A:

Q: The beam-column shown below is pinned at both ends and is subjected to the loads shown. Bending is…

A: Given, PD=534 kNPL=569 kNMDTop=243 kN-mMLTop=206 kN-m  MDBot=125 kN-m  MLBot=64 kN-m  L=4.57 m…

Q: A 3m cantilever beam 260 mm x 485 mm carries a uniformly distributed dead load ( including…

A: P = 567KN M (moment at end) = wL2/8 + PL                                    = 14x32/8 + 28x3…

Q: Considering a horizontal flow sedimentation tank characterized by a flow velocity of precisely 0.32…

A:

Q: Problem 4. From the given data of a differential leveling as shown in the tabulation: Station…

A: To find out the  A) The difference in elevation of station 6 and station 3. B) The difference in…

Q: A beam with a width b=200mm has loads W3D33 kN/m and P-14 kN. If the allowable bending stress is…

A: P=14kN w=33kN/m b=200mm To find h

Q: PROBLEM 1: A barge is pulled by two tugboats. If the resultant of the forces exerted by the tugboats…

A:

Q: (b) A uniform concrete slab of weight, W (kN) is to be attached to two cables which lower ends are…

A: Data Given: Asked: Ratio of the area of rod BE and CF Required weight W of the slab that can be…

Q: A 90-Pa capacity manometer has a reading error of + 0.421 mm. Determine the ratio of d/D so that the…

A:

Q: A simply supported beam has loads P1=71 kN, P2=47 kN, and P3=37 kN. Calculate the deflection at C in…

A:

Q: An infinite slope is shown in the figure. The shear strength parameters at the interface of soil and…

A:

Q: Problem 2 If P= 8.571 kN, Determine the stress in member CE assuming that the area in steel is 24…

A:

Q: 1) You have used a Manning n value of 0.009 for the open channel in the lab. You would expect…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: The motion of pin P is guided by slots cut in rods AD and BE. Knowing that bar AD has a constant…

A:

Q: Draw the A 5 m 150 KN B 5m correct bending moment diagram for the given beam.

A: Solution: Equilibrium condition: ∑Fy=0 Summation of all vertical forces is equal to zero. RA+RC=150…

Q: A wooden block is supported by two guywires as shown in the figure. The tension in the wires are T1…

A:

Q: Calculate the maximum moment for the given moving loads shown. Given: P=49.05 kN x-3.29 m P 25m

A: Maximum bending moment will occur at center.

Q: AWT305 x 41 standard steel shape is used to support the load shape to the centroidal axis are shown…

A:

Q: Hollow shaft AB (4" outside diameter, 3.5" inside diameter) is made of aluminum (E=10x106 psi,…

A:

Q: Three standard mortar cubes were made using non-potable water available at the job site, and three…

A: ASTM standards states that ; The Compressive strength for test results can be acceptable when ; - If…

Q: From the beam shown in the figure. 50 N 20 N Af D -2m -4m- Im- R1 O Compute the deviation of A with…

A: Given data:

Q: I x,0= 10 " I yo = r x,0 = 4"X6"X ½" r yo = 12" 4"X 8"X 1" | 1" 12 "

A:

Q: r is designed to ca 20KN. Using allow 20MPa and ỢC = 6

A:

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: First calculate the force in rod CD. Then calculate the elongation in the same. Then using similar…

Q: Given a two-dimensional blunt wedge immersed in a water stream, velocity profiles are measured both…

A: Solution:-

Q: 6. In the manometer shown at right, containing mercury (s.g.-13.6) from A to B, and oil (s.g.=0.85)…

A: Given Data  Determined the pressure at point C.

Q: diagram and fbd

A: given-a continuous beam subjected to UDL and point load. required-to determine shear force and…

Q: A prestressed concrete beam 223mm x 677mm has the following service loadings PDL=67 KN PLL=44 KN…

A:

Q: 4.26 The PDF of an initial variate with a gamma distribution is v(vx)k-1 fx(x) = ·e-"; x ≥ 0; k > 1…

A:

Q: A truck with axle loads shown rolls across a 10-m span. Compute the maximum bending moment and…

A: l = 10m P1 = 20KN P2 = 10KN P3 = 40KN

Q: Determine the unknown bearings for the traverse courses shown in Figure D. L / 83°10' 28° 11'…

A:

Q: A cantilever beam with P1-79 kN, P2=62 kN and w-33 kN/m has the loadings shown. Calculate the…

A:

Q: largest uniformly distributed load that can be applied over the right two-thirds of the beam if the…

A: ΣMR1=0 3R2=2w(2) R2=4/3w  ΣMR2=0 3R1=2w(1) R1=2/3w  (fb)max = Mc/I Where,        (fb)max = 60MPa…

Q: Problem 2. Determine the following unknowns on the beam shown below using Area-Moment Method.…

A: Given data : E=80 GPa beam section = (150mm*150mm)

Q: A 12m beam will be subjected to the following loads: Uniform dead load due to self weight = 28.6…

A:

Q: = 1.5 m in a soil with [5] The base of a square footing with 2 m wide rests at a depth Df parameters…

A:

Q: 4.144 Find the forces in members HC and HG in terms of P. -1.5 m--1.5 m--1.5 m- A B C D 1 m 2 m H. 3…

A: This problem is related to truss from structure analysis. In this question we find out Force in…

Q: Problem: Draw the shear and moment diagram of the given beam. 100 kN B 75 kN - m 3 m- -3 m- -3 m- m-

A: Using section method to determine the shear force and moment at any section of beam.

Q: 2. For the given system below, find the reactions exerted by the pin and the roller on the beam.…

A: Given data in question  Overhanging beam  Span member length  UDL UVL Point load  To find out…