An iron-ring of mean length 30 cm is made of three pieces of cast iron, each has the same length but their respective diameters are 4, 3 and 2.5 cm. An air-gap of length 0.5 mm is cut in the 2.5 cm piece. If a coil of 1,000 turns is wound on the ring, find the value of the current it has to carry to produce a flux density of 0.5 Wb/m² in the air gap. B/H characteristic of cast-iron may be drawn from the following : ans: 0.58A B(Wb/m2) 0.1 0.2 0.3 0.4 0.5 0.6 Н(АTm) 280 620 990 1400 2000 2800

An iron-ring of mean length 30 cm is made of three pieces of cast iron, each has the same length but their respective diameters are 4, 3 and 2.5 cm. An air-gap of length 0.5 mm is cut in the 2.5 cm piece. If a coil of 1,000 turns is wound on the ring, find the value of the current it has to carry to produce a flux density of 0.5 Wb/m² in the air gap. B/H characteristic of cast-iron may be drawn from the following : ans: 0.58A B(Wb/m2) 0.1 0.2 0.3 0.4 0.5 0.6 Н(АTm) 280 620 990 1400 2000 2800

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

QUESTION 3 4 In a ferromagnetic material, the relation between flux and flux density is O linear O nonlinear O not related O inverse
A flux of 2 mWb passes through a strip of length and breadth 10 cm and 20 cm respectively. It is placed at an angle of 30 degrees to the direction of uniform magnetic field. What is the magnetic flux density ?
In the figure is shown a current of 50 A in a wire 120 cm long and at an angle of 45° to a magnetic field of flux density 6.0 x 10 -4 Wb/m2. What are the magnitude and direction of the force on this wire?
Consider the magnetic circuit in Figure. Assuming that the core µ= 1000µo has a uniform cross section of 4 cm2,N= 400 , the flux density in the air gap. 0.2 A L = 42 cm 4 = 0.1 cm 35.4 mwb 60.5 mwb 70.8 mwb Non of These
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron).
8 We want to produce a flux density of 0.6 T in an air gap having a length of 8 mm. Calculate the mmf required.
5. A cast-iron core of the shape indicated below has the following pertinent dimensions: ab = 10 cm and bc = 15 cm. Find the mmf required if the magnetic field intensity in the thinner side is H1= 100 A-turns/m and the thicker side is H2 = 46 A-turns/m. b 2011
A straight long wire is carrying a current of 1000 A. Find the flux density at a point 1 ft from the wire.
I need the answer as soon as possible
(b) A ferromagnetic is shown in figure Q3(b). Find the value of the current that will produce a flux of 0.005wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. The depth of the core is 5cm. The other dimensions of the core are as shown in the figure. 15 cm 500 turns 15 cm 45 cm 5 сm 15 cm 10 cm 35 cm Figure Q3(b)