An iron block of unknown mass at 85oC is dropped into an insulated tank that contains 100L of water at 20oC. At the same time, a paddle wheel driven by a 200W motor is activated to stir the water. It is observed that thermal equilibrium is established after 20min with a final temperature of 24oC. Assuming that the container is perfectly insulated, determine the mass of the iron block (kg). Use C of IRON= 0.44 kJ/kg-K. draw a figure also, and explain each step by step solution.

Q: How can we demonstrate that equilibrium is a dynamic process by running an experiment? Please…

A: Dynamic equilibrium - Consider an object moving with a certain velocity. The object is acted upon by…

Q: A pressure vessel has an internal volume of 0.5 m3 at atmospheric pressure. It is desired to test…

A: Given data: Internal volume (V1) = 0.5 m3 P = 300 bar Increased volume = 6%V1 Modulus of elasticity…

Q: A rigid tank filled with R-134a is divided into two chambers by a membrane. The membrane is a…

A: As per our guidelines we are supposed to do only 3 subparts, kindly post other part separately.

Q: A mass of gas at an initial pressure of 28 bar, and with an internal energy of 1500 kJ, is contained…

A: Given: P1=28 bar=2800kPa u1=1500kJ u2=1400kJ v1=0.06m3 pv2=constant To find: 1) Work done, W 2)…

Q: Consider the PV diagram as shown above when a thermodynamic system changes its state from state a to…

A:

Q: A gas in a piston-cylinder assembly is compressed (through a combination of external force on the…

A: (a) The given equation is Consider the diagram shown below for the constant pressure compression…

Q: 3 mol of air are contained in a piston-cylinder system with a surface of S = 5 m², loaded with a…

A:

Q: iron block of unknown mass at 85oC is dropped into an insulated tank that contains 100L of water at…

A: Given Data Vw=100 L Ci=0.44 kJ/kgK T1=85°C Tf=24°C

Q: A piston-cylinder arrangement contains water at 112°C, 84% quality with a volume of 0.98 L. What is…

A: The given data is wrong as the spring constant is very high the pressure and enthalpy obtained are…

Q: A dead body was found within a closed room of a house where the temperature was a constant 66 °F. At…

A: Given: Let us consider the given information's, T∞=66°F At t=t+1,  T=75°F At t=0,  T=98.6°F At t=t,…

Q: The specific heat capacity of steel is 450 J/kg⋅∘CJ/kg⋅∘C. Find the amount of heat that is needed to…

A: Given, Specific heat of steel, Cp=450 J/kg °cmass of steel, m=5kgTemperature change, ∆T=(130-0)° c…

Q: Two kilograms of water is contained in a piston-cylinder device where a linear spring is attached to…

A:

Q: A metallic container of fixed volume of 2.5 × 10−3 m3 immersed in a large tank of temperature 27 °C…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: The figure below shows a piston-cylinder assembly fitted with a spring of stiffness k = 29.7 N/m…

A:

Q: A cylinder which is in a horizontal position contains an unknown noble gas at 42100 Pa and is sealed…

A: Calculate the work done in isobaric process. dW = P*dV dW =P*(Pi*r2l)…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.