An insulated pipe, D=26-cm-in diameter and L=15-m-long, is used to transport cold air at m=0.082-kg/s through a building. The pipe is isothermal at T-37°C. Assume that the air flow is thermally and hydro dynamically fully developed. If cold air enters the pipe at 7°C, find the mear exit temperature air (in Kelvin). Note: Use the following as the mean properties of air: k = 0.0265 W/m.°C, v = 16 x 10-6 m2/s, Pr = 0.705 p=1.16 kg/m³, c,=1008 J/kg.K, µ= 185 x 10-7 kg/s-m

An insulated pipe, D=26-cm-in diameter and L=15-m-long, is used to transport cold air at m=0.082-kg/s through a building. The pipe is isothermal at T-37°C. Assume that the air flow is thermally and hydro dynamically fully developed. If cold air enters the pipe at 7°C, find the mear exit temperature air (in Kelvin). Note: Use the following as the mean properties of air: k = 0.0265 W/m.°C, v = 16 x 10-6 m2/s, Pr = 0.705 p=1.16 kg/m³, c,=1008 J/kg.K, µ= 185 x 10-7 kg/s-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
In this problem our goal is to compare pressure drop for the flow of an incompressible fluid in a straight pipe to the pressure drop of a compressible fluid in the same pipe and under the same conditions. For the incompressible case, consider the flow of water at a rate of 5000 lbm/s in the pipe. Then compare the results with the flow of air. The pipe is smooth and has a diameter of 1 in and length of 20 ft. For both cases, fluid enters the pipe at 14.7 psia and 100 F and leaves the pipe at the same temperature.
If 1 cubic meter of water at 0°C is frozen and cooled to -8 degree Celsius by being in contact with a great deal of ice at -8 degree Celsius, estimate the total change in entropy of the process. Given : Required : Illustration: Solution: final answer:
its thermodynamics but didnt find it in the filter sorry
A fully developed flow of air at 27°C flows at 3m/s in a pipe of internal diameter 1cm. A heater surrounds last 20cm of pipe and supplies constant heat to bring the air out at 40°C. The power input needed is
A fluid enters with a steady flow of 3.7 kg/s and an initial pressure of 690 kPa, an initial density of 3.2 kg/m3, an initial velocity of 60 m/s, and an initial internal energy of 2000 kJ Ikg. It leaves at 172 kPa, p = 0.64 kg/m?, v = 160 m/s, and u = 1950 kJ/kg. The heat loss is found to be 18.6 kJ /kg. Find the power in kW.
A steam power plant is located in the northern part of the country. Steam in the plant flows steadily through a 0.203-m diameter pipeline from the steam generating unit (SGU) to the steam turbine. At the SGU end, the steam conditions are determined to be P= 4 mPa, t - 400 celsius, h =3,264.9kJ/kg, and specififc volume = 0.121 m3/kg. At the steam turbine end, the conditions are found to be P=3.5 mPa, t = 392 celsius, h = 3,133.9 kJ/kg, specific volume 0.261m3/kg. Heat loss from the pipeline is 6.92kJ/kg. Determine the steam mass flow rate in kg/s.
Prove this equation for the frictional adiabatic process in a fixed cross-section duct.(Dont handwriten)
B9
30°C, 10m/s 2m Electronic components inside D= 20cm Figure 5 You are designing components of an electronic systems that needs to be inside a 2 m long horizontal duct. The components are sensitive so the cooling mechanism is only done by air flowing over the duct at 30°C and 10 m/s. Initially you proposed a square cross-section with 20-cm length for the duct but is rejected by your client because they said a circular cross- section is better. If the surface temperature of the duct cannot exceed 60°C, find the maximum power rating in kW of the electronics devices that can be located inside the circular cross-section duct. Is it true that circular cross-section is better than a square one for this application?
Five hundred kilograms per hour of steam drives a turbine. The steamenters the turbine at 44 atm and 450C at a linear velocity of 60 m/sand leaves at a point 5 m below the turbine inlet at atmosphericpressure and a velocity of 360 m/s. The turbine delivers shaft work at arate of 70 kW, and the heat loss from the turbine is estimated to be 104kcal/h. Calculate the specific enthalpy change associated with theprocess
a] Steam at 280 oC, tube=26 W/m. It flows at a speed of 4.0 m/s along a pipe made of iron-steel material with a temperature of 0°C. The inner diameter of the iron-steel pipe is 6.0 cm and the outer diameter is 6.8 cm. In order to reduce the heat transfer, the iron-steel pipe is first covered with 2.0 cm thick glass wool (k = 0.38 W/m. oC), then with another 3.5 cm thick insulation material (k = 0.01 W/m. oC). The insulated iron-steel pipe is in the atmospheric environment where the temperature is 18 oC. The convective heat transfer coefficient on the outside atmospheric side of this pipe, where the steam flows, is 36 W/m2. oC, the film heat transfer coefficient on the steam side is 80 W/m2. Calculate the heat transferred per unit pipe length (W/m), since it is known to be °C. b] Calculate the thickness of the material when the pipe is sheathed externally with a material with a thermal conductivity of k=0.02 W/m.oC in order to reduce the heat to be transferred by 20% in the unit pipe…