Don't use Ai An initial time study was done on a process with the following results (in minutes). Based on the dataobtained so far, assuming an allowance of 25 percent of the normal time,Question Viewer timate for the time per customer served, based on this preliminary sample? (Round allintermediate calculations to two decimal places.)The time per unit customer served isminutes. (Enter your response rounded to two decimal places.)An initial time study was done on a process with the following results (in minutes). Based on the data obtained so far, assuming an allowance of 25 percent of the normal time,Question Viewer timate for the time per customer served, based on this preliminary sample? (Round all intermediate calculations to two decimal places.)Performance Obs Obs Obs Obs ObsElementElement 1Rating1234511066556Element 21208810Element 3907788The time per unit customer served is minutes. (Enter your response rounded to two decimal places)

I hope you find this helpful. If you have any question or clarification, do not hesitate to reach…

Answered: An initial time study was done on a…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

A customer service department has the following resolution response time data: Average Response Time First contact 0.25 hr. Service scheduling 0.50 hr. Wait for service 24.00 hrs. Service 1.50 hrs. Total resolution time 26.25 hrs. What is the value-added ratio (rounded to one decimal place) in this process? a. 8.6% b. 91.4% c. 5.7% d. 28.6%
How reliable is the result of work sampling activity in determining working time and idle time of the operator?
poease answer within 30 minutes
An analyst made 30 observations over 15 minutes during which 12 units where produced. For 9 observations, the worker was seen working. Compute for the observed time.
What would typically happen if an abnormally short time was recorded when conducting a stopwatch time study? a) It would be included in the study. b) It would be discarded. c) It would be factored by the performance rating. d) Inform the supervisor of the abnormality.
At Dominos pizza the time study restaurant yielded an average observed time of 4.0 minutes. The analyst rates the observed worker at 85%.this means the worker performed at 85% of normal when the study was made. The firm uses a 13% allowance factor. What is the standard time for this operation. 9.3 min 3.4 min ✓ 3.9 min 3.8 min
company from your understanding. 3) Calculate the standard time for an operation from the following data. Average observed time for manual elements = 4 0 minutes Average auto cycle time = 3 minutes Rating on a scale of 100 = 90% Personal & other allowances = 15% of basic time
Management of Mittel Rhein AG of Köln, Germany, would like to reduce the amount of time between when a customer places an order and when the order is shipped. For the first quarter of operations during the current year the following data were reported: Inspection time- 0.7 daysWait time (from order to start of production) -16.6 daysProcess time -2.7 daysMove time -1.3 daysQueue time- 4.5 daysRequired:1. Compute the throughput time. (Round your answer to 1 decimal place.) 2. Compute the manufacturing cycle efficiency (MCE) for the quarter. (Round your answer to the nearest whole percentage (i.e., 0.12 should be entered as 12).) 3. What percentage of the throughput time was spent in non–value-added activities? (Round your answer to the nearest whole percentage (i.e., 0.12 should be entered as 12).) 4. Compute the delivery cycle time. (Round your intermediate calculations and final answer to 1 decimal place.) 5. If by using Lean Production all queue…
b) The normal time for this operation = enter your response here minutes (round your response to three decimal places).
An analyst has been asked to prepare an estimate of the proportion of time that a turret lathe operator spends adjusting the machine, with 90% confidence level. Based on previous experience, the analyst believes the proportion will be approximately 30%. a. If the analyst uses sample size of 400 observations, what is the maximum error that will be associated with the estimate? b. What sample size would the analyst need in order to have the maximum error be no more than +/- 5%?
A restaurant has had many visitors in the past month, this has happened since the restaurant went viral on social media. The advantages of this restaurant in addition to delicious, healthy and affordable food. The food products of this restaurant are of high quality and very able to compete with existing competitor restaurants. Plus the design of the restaurant is very attractive or instagrammable. As a result of this, the workforce in the restaurant is overwhelmed with the number of consumers at lunch and dinner hours. Restaurant owners are considering increasing the number of employees but worry that this trend is temporary. What solutions can the owner do to serve the booming customers at lunch and dinner hours? In addition, the owner is also worried that the food menu will not last long and provide satisfaction to customers. Explain your solution!
Compare stopwatch time study and work sampling.

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS