An industrial heater has a nameplate that reads: 1) What is the apparent power? 225 Vrms 51 Hz 190 kVA 0.86 lagging 3) What is the reactive power? 208 Vrms 44 Hz 58 KVA 0.84 lagging 432 Vrms 58 Hz 2) What is the real power? 7 kVA 195 Vrms 56 Hz 4) What is the magnitude of the impedance of the heater? 196 kVA 0.75 lagging 0.74 lagging

An industrial heater has a nameplate that reads: 1) What is the apparent power? 225 Vrms 51 Hz 190 kVA 0.86 lagging 3) What is the reactive power? 208 Vrms 44 Hz 58 KVA 0.84 lagging 432 Vrms 58 Hz 2) What is the real power? 7 kVA 195 Vrms 56 Hz 4) What is the magnitude of the impedance of the heater? 196 kVA 0.75 lagging 0.74 lagging

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Answer it with complete explanation.....
PLEASE ANSWER QUICKLY
A voltage waveform is shown below, please find its RMS voltage value. Choose the value that is closest to the answer. NEED A NEAT HAND WRITING ONLY OTHERWISE WILL LEAVE A DOWNVOTE NO CHAT GPT MINIMUM3 STEPS WITH EXPLANATION
Instantaneous power output of a single phase 60 Hz generator will not be constant only under following condition: O A. The load draws only real power. O B. The load draws only reactive power. O C. None of the other choices are correct O D. The load is unbalanced. O E. The load draws bothreal and reactive power.
... 0.25 A 120 V 60 Hz RL 1 k2 470 µF When the circuit is working normally, it has an rms secondary voltage of 12.49 volts. Considering the ripple voltage, what is thnimum dc load voltage?
The rotor of a 4-pole ac generator is wound with a 200 turns coil. If the flux per pole is 5 mWb and the rotor runs at a speed of 1500 rpm, the rms value of the induced voltage for this AC generator is nearly?
The peak amplitude of the sinusoidal voltage source in the circuit shown in (Figure 1) is 150√2 V and its period is 200 μs. The load resistor can be varied from 0 to 20 2 and the load inductor can be varied from 1 to 8 mH Part A Calculate the average power delivered to the load when R = 10 and Lo = 6 mH Express your answer to three significant figures and include the appropriate units. P = 9.00 W Figure 300 Ω w 1μF Ro 1 of 1 Submit Previous Answers Correct Determine the settings of R, and Lo that will result in the most average power being transferred to Ro Part B Find Ro Express your answer to three significant figures and include the appropriate units. НА ? Ro= Value Units Submit Request Answer Part C Find Lo Express your answer to three significant figures and include the appropriate units. HA ? Lo= Value Units Submit Request Answer
A 43mH coil in series with a 1200 ohm resistor across a sine wave ac voltage source with a frequency of 6 kHz. The total impedance for the circuit is O 1620 46.5° ohm esc 2017 53.5° ohm 1200 53.5° ohm 2820 46.5° ohm ! 1 Q ← 2 W #3 C E $ 54 R G Search or type URL % 5 MacBook Pro T A 6 Y & 7 ☆ U * 8 + 1 ( 9 ( 0 ) 0 4) P + O = [ delete
4 N -is n 6 0 -j8 N js N 220/-30° V Figure 3. Referring to figure 3, determine the rms current at j52 reactance (inductor) using KCL (Answer must be in polar form and should be in 4 decimal places). Referring to figure 3, determine the rms voltage at j52 reactance (inductor) using KVL (Answer must be in polar form and should be in 4 decimal places).
The average value of a sinusoidal current is 300A. What is it’s rms value? Group of answer choices 444 A 202 A 333 A 101A
An alternating current varying sinusoidally with a frequency of 50Hz has an RMS value of 20A. (i) Write down the equation for the instantaneous value (ii) find the value of (i) at 0.0025 second I need for every correct steps
Referring to figure 3, determine the rms current at j5Ω reactance (inductor) using KCL(Answer must be in polar formand should be in 4 decimal places).