An ideal transformer is connected to a voltage source given by es(t) = 100cos(2000nt)V on the primary side. Transformer turn ratio is 10. There is a load connected on the secondary side that is consuming 20VA at 70% leading power factor. Draw a well-labeled circuit diagram and calculate: (i) Primary and secondary currents in time domain (ii) Individual components of load

An ideal transformer is connected to a voltage source given by es(t) = 100cos(2000nt)V on the primary side. Transformer turn ratio is 10. There is a load connected on the secondary side that is consuming 20VA at 70% leading power factor. Draw a well-labeled circuit diagram and calculate: (i) Primary and secondary currents in time domain (ii) Individual components of load

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
DC 200 V was applied to the primary of a transformer with a conversion ratio of 1/5. Obtained from seconderexplain the reason for this by typing the voltage value to be?
Q5. A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 2 and a leakage reactance of 0.240. The low voltage winding resistance is 0.05 and the leakage reactance is 0.02 2. Find the equivalent winding resistance, reactance and impedance referred to the (i) high voltage side and (ii) the low-voltage side. (Draw the related equivalent circuits)
An ideal transformer with a 500 turns primary and 125 turns secondary windings delivers 400W to a 40 load. The resistance of the primary windings is 160. Find the primary current and voltage.
An AC source provides peak output Vi and peak current ii when connected to the coil primary of a transformer. The transformer has Np turns in the primary coil and Ns turns in the secondary coil. A resistance circuit R is connected to the transformer, see figure below. What is the equivalent resistance of the circuit?
Regulation for the trans.
Solve it...
Complete the blank An isolating transformer is a (..........................)ratio transformer with several important applications.
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
13)This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course.
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
solve