An ideal reheat turbine with one stage of reheat recieves steam at 8.0 Mpa,500°c.Reheat pressure is 0.83 Mpa and exhaust pressure is 0.007 mpa. The work is 1559kj/kg and the thermal efficiency is 41.05%.Find the temperature of steam leaving the heater.

Q: diesel engine has a compression ratio of 20:2 with an inlet of 90 kPa, 17C, state 1, with volume 0.5…

A: Given Data rc=20.2  State 1: 90 kPa, 17°C Tmax=1900 K

Q: the intake volume of an engine working on the carnot cycle is 43.5 m^3 while the voume after the…

A: The cycle efficiency. Given: The intake volume is V1=43.5 m3. The volume after the compression…

Q: 40˚C. Expansion now occurs to the condenser pressure of 0.0035 MPa. The steam flow is 147,000 kg/hr,…

A: In a reheat cycle steam at 15 MPa, 540˚C enters the engine and expands to 1.95 MPa. Reenters the…

Q: The pump in the Rankine cycle increases the pressure from 20 kPa to 6 MPa. The boiler exit…

A: P1 = 20 kPaP2 = 6 MPa or 6000 kPaBoiler exit temperature, T = 600°CRequired:Q ( heat supplied to…

Q: A milk sterilizer flow system accepts milk at 20°C, 100 kPa and uses steam at 1 MPa, 200°C to heat…

A: The mass flow rate of milk is The properties of steam is The inlet pressure of milk is The inlet…

Q: A reheat steam cycle has 13500 kPa throttle pressure at the turbine inlet and 2800 kPa reheat…

A:

Q: Open feed water heater in the power plant operating according to the Rankine cycle with ideal…

A: Open feed water Rankine Cycle,

Q: An adiabatic air turbine has an inlet of 1600 K, 2000 kPa, and it exhausts at 100 kPa. If o=0.5…

A: The inlet temperature of adiabatic air turbine is .The inlet pressure of the adiabatic air turbine…

Q: Q2. Consider an ideal Rankine cycle in which the working fluid enters the- boiler at 2.5 MPa and…

A:

Q: How much work potential is wasted in power plant that takes in steam at 5 kPa + delivers saturated…

A: Givenwet steam to saturated liquid at constant pressurex=0.85 P=5kPa

Q: In a carnot cycle. The pressure at the end of heat rejection is 15 psia while the pressure at the…

A:

Q: In an ideal steam cycle, steam at (20 bar, 360 C°) is expanded in a turbine to (0.08 bar). It then…

A:

Q: In the open-circuit steam plant, boiler feed water at atmospheric pressure 1 bar and 35oC is pumped…

A:

Q: 4. A two-stage compressor receives 0.35kg/s of air at 100kPa and 269K and delivers it at 5MPa. Find…

A: givenm=0.35kg/sP1=100kPaT1=269KP2=5Mpa

Q: A Brayton cycle has an initial temperature 300C. If compression ratio of compressor is 8, find the…

A:

Q: Ideal air enters a compressor at 100 kPa and is compressed to 150 kPa. The isentropic efficiency is…

A:

Q: In a carnot cycle. The pressure at the end of heat rejection is 14 psia while the pressure at the…

A:

Q: 2. 1 kg/s steam enters the turbine at 2.5MPA and 500C while leaving at 10kPa with 89% quality. The…

A:

Q: Air in an ideal diesel is compresses from 8 liters to 0.15 and then expands during the constant…

A:

Q: Efficiency of Carnot cycle is given as 75%. If the cycle direction is reversed, what will be the…

A: Let us take, Lower temperature of carnot cycle = TL Higher temperature of carnot cycle = TH   Given,…

Q: An ideal turbine with one stage of reheat receives steam at 8 MPa, 500 degree C. Reheat pressure is…

A:

Q: A reheat steam has 13,850kPa pressure at the turbine inlet and a 2800 kPa reheat pressure, the…

A:

Q: A steam engine isentropically expand 5kg/sec of the steam from the 0.70 mpa 250°c, the exhaust is…

A: Given data: - The mass flow rate is ms = 5 kg/s. The initial pressure of the steam is P1 = 0.70…

Q: Problem 2: A turbine accepts steam at 3000kPa and 800 °C and leaves at 100 kPa with a quality of…

A:

Q: In a geothermal power plant a underground hot water is available as saturated liquid at 600 kPa. The…

A: Given:P1=529 kPax1=98%P2=15 kPa

Q: An isentropic turbine process 5kg/s of steam at 4MPa, which is exhausted at 50kPa and 100 C. Five…

A: given data : mass flow rate at which the turbine processes steam (m*1) = 5kg/s pressure at which…

Q: If the Mean Effective Pressure MEP is the ratio of the net work and the volume displaced, find the…

A:

Q: Draw the T-s diagram and Plant Lay-Out A steam power plant has a steam generator (boiler) exit at 4…

A:

Q: An adiabatic turbine receives 2.0 kg/s of superheated steam at 2.5 MPa, and 700°C. The discharge at…

A:

Q: A reheat steam cycle has 13500 kPa throttle pressure at the turbine inlet and 2800 kPa reheat…

A:

Q: If the mass flow rate for air is 5 Kg/s .and air compressor takes in air at 200 kPa, 290 K and…

A: Assumptions are taken in the compressor device -Air is assumed as an ideal gas -Flow is steady -No…

Q: 1 kg/s steam enters the turbine at 2.5MPa and 500C while leaving at 10kPa with 89% quality. The pump…

A: Answer: (a) The turbine work output is 1142.03 kW. (b) The heat added in the boiler is 3268.4751 kW.…

Q: A reheat steam cycle has 13500 kPa throttle pressure at the turbine inlet and 2800 kPa reheat…

A:

Q: An ideal turbine with one stage of reheat receives steam at 8 MPa, 500°C. Reheat ressure is 0.8 MPa…

A:

Q: Butane enters an adiabatic compressor at 20psia and 250F with a volume Clow rate of 12ft3/s and…

A:

Q: 2. Consider an ideal steam reheat cycle where steam enters the high-pressure turbine at 3.0 MPa,…

A:

Q: Find the boiler heat transfer including the reheat process (kW)

A:

Q: Find the efficiency of Ideal Brayton cycle having pressure ratio of 8. What will be new efficiency…

A: Given data pressure ratio(rp) = 8 pressure ratio(rp)=10

Q: Q2Air enters an insulated turbine at 50°C, and exits the turbine at -30°C, 100 kPa. The isentropic…

A: