An ideal Otto cycle is a cycle in which: Select one: O a. The heat addition occurs at constant pressure and the heat rejection occurs at constant pressure O b. None of the options O c. The heat addition occurs at constant pressure and the heat rejection occurs at constant volume O d. The heat addition occurs at constant volume and the heat rejection occurs at constant volume A BMW V6 square gasoline engine operating at 3500 rpm has a mechanical efficiency of 82%. The cylinder bore is equal to 86 mm and the connecting rod length is 16 cm. The compression ratio of the engine is 9 and the indicated mean effective pressure is 1250 kPa. The indicated power is: Select one: O a. 97.6 kW O b. 125.1 kW O c. 174.7 kW O d. 109.3 kW

An ideal Otto cycle is a cycle in which: Select one: O a. The heat addition occurs at constant pressure and the heat rejection occurs at constant pressure O b. None of the options O c. The heat addition occurs at constant pressure and the heat rejection occurs at constant volume O d. The heat addition occurs at constant volume and the heat rejection occurs at constant volume A BMW V6 square gasoline engine operating at 3500 rpm has a mechanical efficiency of 82%. The cylinder bore is equal to 86 mm and the connecting rod length is 16 cm. The compression ratio of the engine is 9 and the indicated mean effective pressure is 1250 kPa. The indicated power is: Select one: O a. 97.6 kW O b. 125.1 kW O c. 174.7 kW O d. 109.3 kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cylinder of an Ideal Dual Combustion Cycle,, with a pressure ratio of 2, has a bore of 7 inches and a stroke of 7.5 inches. The 4-stroke, 4-cylinder engine operates at 6000 rpm having a compression ratio of 21 and a cut-off ratio of 1.34. Air enters with a temperature and pressure of 67°F and 15 psi. Determine the following:a. Pressure & Temperature at each state.b. Power output of the engine (hp).c. Thermal Efficiency.
An ideal Rankine cycle operates between the pressure limits of 6 bar and 0.1 bar with steam as the working fluid (data above). Saturated water leaves the condenser and the turbine inlet temperature is 250°C. You may assume that the work input to the boiler feed water pump is negligible. Estimate the efficiency of the cycle and determine the turbine power in kJ/kg.
An Otto cycle engine operates with the cycle shown below. The air in the engine can be considered a perfect gas with k = 1.402, R = 0.28 kJ/kgk and c, = 0.71 kJ/kgK. The engine has the following known states: State 1: p₁ = 1bar, V₁ = 0.5x10-3 m³, T₁ = 300K State 2: T₂ = 725K, rc = 9 State 3: T3 = 2196.1 K Р What is the specific heat transfer from state 3-4? Please enter your answer in kJ/kg Answer:
1. What is the specific enthalpy at the outlet of the turbine and compressor in KJ/Kg 2.what is the power output per unit mass flow rate of air of the turbine . 3.what is the rate of heat input per unit mass flow rate of the air during the heat addition process
Consider the operation of the ideal Brayton cycle with a regenerator. The maximum temperature in the cycle is set. What happens with increasing pressure ratio? Group of answer choices The amount of heat added in the cycle up to a point will decrease with net work output remaining the same and thermal efficiency will increase. Thermal efficiency will increase Compressor exit temperature will increase with turbine exit temperature remaining the same. When the two temperatures are equal, the benefit of the regenerator will be zero. Thermal efficiency will decrease
Please solve the question on the sheet and get a clear picture and submit the picture. thankyou
please provide full solution
Thermodynamics Instructions: Draw the T-s and Schematic diagram for this problem
Combustion Engineering 4 decimal places
I need the answer as soon as possible
The gas turbine engine is a single-spool engine; it will be modified, and a free power turbine will be added and connected to an electric generator. The picture shows a schematic diagram of the modification. Comment on the sources of losses in this ideal gas turbine cycle and how this losses could be minimised.
A Joule cycle is used for electricity production in a power plant. Air is introduced to the cycle from the ambient with a pressure of 1 bar, and a temperature of 20 °C. The air is compressed in compressor C1 and is thereafter cooled down to 30 °C. The air is compressed again in compressor C2. The air passes through a regenerator where it is heated by exhaust gases. Heat is added by combustion of fuel in combustion chamber CC1. The air is thereafter expanded in turbine T1. The air is reheated in combustion chamber CC2. The air is expanded in turbine T2, and the exhaust gases after the turbine pass through the regenerator and is finally vented to the ambient. Turbine T2 is driving compressor C2. The net work from the cycle is produced by the difference between the work produced by turbine T1 and compressor C1. The regenerator efficiency is 0.80, the isentropic efficiency of the compressor is 0.83, and for the turbine 0.85. The temperature after CC1 and CC2 is tCC, the pressure after…