An ideal monatomic gas undergoes a reversible expansion to 1.5 times its original volume. In which ofthese processes does the gas perform the least amount of work?O if the pressure decreases in proportion to the volumeO if the pressure increases in proportion to the volumeadiabaticallyO at constant pressureO at constant temperaturePregunta 5An ideal monatomic gas undergoes a reversible expansion to 1.5 times its original volume. Inwhich of these processes does the gas have the largest loss of internal energy?Oat constant pressureif the pressure decreases in proportion to the volume.adiabatically.at constant temperature

The least work done is in adiabatic process. We can understand it by p-v diagram of Carnot Cycle. We…

Answered: An ideal monatomic gas undergoes a…

Similar questions

For ice melting into water at 0 °C, the latent heat of fusion is Lp = 3.34 x 105 J/kg. For water boiling at 100 °C, the latent heat of vaporization is Ly = 2.26 x 105 J/kg. Which process involves a greater change in entropy? O melting 1.00 kg of ice at 0 °C O vaporizing 1.00 kg of liquid water at 100 °C the entropy change is the same for both
An a car engine operating at 1.85 10-1 rev/min, the expansion of hot, high-pressure gas against a piston occurs in about 10 ms. Because energy transfer by heat typically takes a time on the order of minutes or hours, it's safe to assume that little energy leaves the hot gas during the expansion.Estimate the work done by the gas on the piston during this adiabatic expansion by assuming the engine cylinder contains 0.160 moles of an ideal monatomic gas which goes from 1.200 103 K to 4.00 102 K, typical engine temperatures, during the expansion.J
Question B: A sample of 1.00 mole of a diatomic ideal gas is initially at temperature 265 K and volume 0.200 m3. The gas first undergoes an isobaric expansion, such that its temperature increases by 110.0 K. It then undergoes an adiabatic expansion so that its final volume is 0,440 m3. i. Sketch a PV diagram for the two-step process, including labeled initial, final, and intermediate states, and a two-part curve/path with an arrow indicating direction. Label the initial state "i", the final state "f", and the intermediate state "b". Write down the known values for P, T, and V at each point, e.g. T; = 265 K, and Th = 375 K. (B.1) What is the initial pressure of the gas, Pi, in pascals [Pa]? Pi = Pa Enter a number. (B.2) What is the total heat transfer, Q, to the gas, in joules [J]? Q = Qtotal = (B.3) What is the total work done on the gas, w, in joules [J]? w = Wtotal = Enter your answer for problem (B.3) for credit. First, use the following questions as intermediate steps; answers can…
Consider a process that uses n moles of a monatomic ideal gas operating through a Carnot cycle. The initial temperature and pressure of the gas are T1 and P1, respectively. Consider steps 1 → 2, 2 → 3, 3 → 4, and 4 → 1. a. In the adiabatic heating, the temperature of the gas is doubled. Write an expression for the volume V3 after this step in terms of V1. b. Write an expression for the volume V4 in terms of V1.
A monatomic gas is take through a cycle from A to B to C and back to A. At A the pressure is 100,000 pa, the volume is 4.0 liters, and the temperature is 300K. The gas is compressed adiabatically until the volume is 1.0 liters (at B). How much energy was given to or removed from the gas during the adiabatic process?
An object can have its entropy decrease only if... O heat flows into the object. O work is done on the object. O There is no way for an object have its entropy decrease. O something else has its entropy increase by at least as much.
A certain gasoline engine is modeled as a monatomic ideal gas undergoing an Otto cycle, represented by the p-V diagram shown in the figure. The initial pressure, volume, and temperature are p1 = 1.05 × 105 Pa, V1 = 0.035 m3, and T1 = 290 K, respectively. a)The first step in the Otto cycle is adiabatic compression. Enter an expression for the work performed on the gas during the first step, in terms of V1, V2, and p1. b) Calculate the temperature of the gas, in kelvins, at the end of the first step. c)The fourth and last step in the Otto cycle is isochoric cooling to the initial conditions. Find the amount of heat, in joules, that is discharged by the gas during the fourth step.
Find the work for a system where temperature (T) is constant. (This is called an isothermal process) W = P(V₂ - Vf) W = 0 (V) W = P(V₁ - V₂) W = PV W = - PV) W = -nRT W = nRT W = nRT In W n(V) = nRT In
An ideal gas undergoes the thermodynamic process shown in the ??PV diagram in the figure. Determine whether each of the values (a) Δ?ΔU, (b) ?W, (c) ?Q for the gas is positive, negative, or zero. (Note that ?W is the work done ??on the gas.) Hint: First use the ideal gas law to find the initial and final temperatures in terms of ?0P0 and ?0V0 and determine if the final temperature is greater than, less than, or equal to the initial temperature. (a) ΔU A.+ B.- C.0 (b) W A.+ B.- C.0 (c) Q A.+ B.- C.0