An ideal fluid flows through a horizontal pipe whose diameter varies along its length. Measurements would indicate that the sum of the kinetic energy per unit volume and pressure at different sections of the pipe would (a) decrease as the pipe diameter increases, (b) increase as the pipe diameter increases, (c) increase as the pipe diameter decreases, (d) decrease as the pipe diameter decreases, or (e) remain the same as the pipe diameter changes.

An ideal fluid flows through a horizontal pipe whose diameter varies along its length. Measurements would indicate that the sum of the kinetic energy per unit volume and pressure at different sections of the pipe would (a) decrease as the pipe diameter increases, (b) increase as the pipe diameter increases, (c) increase as the pipe diameter decreases, (d) decrease as the pipe diameter decreases, or (e) remain the same as the pipe diameter changes.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A block of wood floats in fresh water with 0.834 of its volume V submerged and in oil with 0.899 V submerged. Find the density of (a) the wood and (b) the oil. (a) Number (b) Number i HI i Units Units >
A tank in the shape of an inverted cone has a height of 20 meters and a base radius of 11 meters and is filled with liquid to a depth of 16 meters. Determine the amount of work needed to pump all of the liquid to a point 1m from to the top of the tank. Assume that the density of the liquid is 793 kg/m 3
AST Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y 12.5 cm below point 1. The water pressure at point 1 is 3.20 x 10 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 x Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. m/s (b) point 2 x Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. m/s
The stream function for a fluid flow is given as w(x,y) =20 In(x2 + y) Its velocity potential is O 0- 40 tan O None from these answers 0= - 40 tan $=-40 tan" 00=40 tan(xy) 40 tan
Blood flows through a 1.66 mm diameter artery at 26 mL/min and then passes into a 600 micron diameter vein where it flows at 1.2 mL/min. If the arterial blood pressure is 120 mmHg, what is the venous blood pressure? Ignore the effects of potential energy. The density of blood is 1,060 kg/m3. 1,000 L = 1 m3
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.700 L/s, with an output pressure of 2.00 x 105 N/m². You may neglect frictional losses in both parts of this problem. (a) The water enters a hose with a 3.00 cm inside diameter and rises 3.00 m above the pump. What is its pressure (in N/m²) at this point? N/m² (b) The hose goes over the foundation wall, losing 1.70 m in height, and widens to 4.00 cm diameter. What is the pressure now (in N/m²)? N/m²
Balloon angioplasty is a technique to restore blood flow through coronary arteries that have been narrowed by the build-up of plaque. The surgeon threads a catheter into the coronary artery, then inflates a balloon that compresses the plaque against the wall of the artery. Suppose a diseased coronary artery has a diameter of 2.0 mm. To what diameter must it be expanded to increase the blood flow by a factor of 5.0 with no change in pressure?
When you hold your hands at your sides, you may have noticed that the veins sometimes bulge—the height difference between your heart and your hands produces increased pressure in the veins. The same thing happens in the arteries. Estimate the distance that your hands are below your heart. If the average arterial pressure at your heart is a typical 100 mm Hg, what is the average arterial pressure in your hands when they are held at your side?
the water faucent for a garden hose is tuned on, but with the nozzle turned off the owner of the garden assumes that the water cannot exit the hose. however , even through the hose lies horizonatlly on the ground, the owner notice a stream of water spraying vertically out a small leak in the hose. to a height of 0.75 m. what must be the pressure of the water inside the hose 1) 7.9 kpa 2) 8.8 kpa 3) 7.4 kpa 4) 101.3 pka
(c) Water is circulating through a closed system of pipes in a two-storey house. On the ground floor, the water has a gauge pressure reading of 3.5 × 105 Pa and has a speed of 2.1 m/s. However, on the upper floor, which is 3.8 m higher, the speed of the water is 3.7 m/s. The pipe widths are different on the two floors. Calculate the pressure of the water on the upper floor of the house? Take the density of water to be 1000 kg/m
Fire hoses used in major structure fires have inside diameters of 6.4 cm. Suppose such a hose carries a flow of 40 L/s starting at a gauge pressure of 1.62 × 10°N/m². The hose goes 10 m up a ladder to a nozzle having an inside diameter of 3 cm. Assume negligible resistance, density of water is 1000 kg/m³, and atmospheric pressure = 1.013×105 Pa. Using the flow rate (a) Calculate the velocity at the start of the hose. V = start m/s (b) Calculate the velocity at the nozzle. V = nozzle m/s Pnozzle (c) Calculate the gauge pressure at the nozzle, P, If nozzle <3%, then enter P nozzle =0, else P atm |P nozzlel enter the calculated value. If atm <3%, then we are going to assume that the absolute pressure at the nozzle is approximately equal to the atmospheric pressure, making the gauge pressure almost zero when compared to the atmospheric pressure. Pnozzle Pa