An FM signal with modulation index ß which the carrier component of the FM signal is reduced to zero for the second time, is transmitted through an ideal band pass filter with frequency of fc: carrier frequency and band width 4fm (fm: modulating signal), modulating frequency = 1 KHz, assume the amplitude of both carrier and modulating is one. Determine the possible spectrums of the filter output What is the frequency sensitivity of the modulator? Determine the average power of the FM by using Bessel function formula

An FM signal with modulation index ß which the carrier component of the FM signal is reduced to zero for the second time, is transmitted through an ideal band pass filter with frequency of fc: carrier frequency and band width 4fm (fm: modulating signal), modulating frequency = 1 KHz, assume the amplitude of both carrier and modulating is one. Determine the possible spectrums of the filter output What is the frequency sensitivity of the modulator? Determine the average power of the FM by using Bessel function formula

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw frequency response curve of a bandpass filter whose end frequencies are 0.1 MHz and 0.4 MHz respectively. Consider peak amplitude as 1. Use your own scale and necessary values.
Problem A For the Circuit Shown: Derive the equation for the magnitude of the gain. Include a detailed set of steps Begin with the given circuit. Each step should include an explanation (example, circuit analysis theorem, math step). O Va Provide a sketch of the Bode Plot for the magnitude of the gain. Use the two- asymptote representation in addition to other curves and information as needed. Indicate the 3db frequency, the gain in the passband, axis identifiers along with units. For the equation for magnitude of the gain, plug in frequencies 0 Hz and "infinite” Hz (this can be considered several multiples of the 3db frequency). Approximate the magnitude at these 2 frequencies and highlight the frequencies on the Bode Plot. R Vb с
1) From the plots, what is the frequency of the input signal (in samples as well as radians)? 2) From the plots, what is the frequency of the output signal (in samples and radians)? 3) What does echo do to the magnitude and phase spectra?
Explain how does LCR circuit work, impedance of LCR circuit in resonance, condition for resonance in LCR circuit and also discuss quality factor in LCR circuit?
I need the answer as soon as possible
I need the answer as soon as possible
k1=35 k2=80
very urgent
a. Find the value of Xc for resonance. b. Determine the total impedance of the circuit at reso- nance. c. Find the magnitude of the current I. d. Calculate the voltages VR, V1, and Vc at resonance. How are V1 and Vc related? How does VR compare to the applied voltage E? e. What is the quality factor of the circuit? Is it a high- or low-Q circuit? f. What is the power dissipated by the circuit at reso- nance? + VR - + V1. ll R = 20 N X = 402 E 100 mV Xc Vc
Q2) A radar receiver with a 50 2 input resistance operates at a temperature of 29°C. The received signal frequency, bandwidth and signal voltage shown in table also it is applied to an amplifier with a noise figure (NF) shown in the same table. Calculate the following: i) The input noise power, PN. ii) The input signal power, Ps. iii) Signal to Noise Ratio in decibels, SNR. iv) The noise factor F and SNR of the amplifier. v) The noise temperature of the amplifier. (Given Boltzmann constant, k = 1.38x1023) Student name signal frequencybandwidth signal voltage|noise figure (NF) LAKSHMI 80 4 7µV 2.5 dB LJINA 60 16 |6µV 2.4 dB MAZOUN 90 15 8uV 2.6 dB MOHAMMED 70 6 5 μν 2.3 dB
1) How can I calculate cutoff frequency, resonance frequency, bandwidth in a filter? 2) What is their formulas?
b. What is the channel capacity for signal power of 250 W, noise power of 50 W, and bandwidth of 3 MHz? c. What is the channel capacity when the S/N ratio is doubled but the bandwidth is reduced by a factor of 5?