An engine operates in an Air-standard Diesel cycle. The net work is 800 kW with air mass flow rate of 5 kg/s. If the maximum temperature is 4000K and the temperature at the end of the isentropic compression is 1000K,find the heat added, efficiency and compression ratio

An engine operates in an Air-standard Diesel cycle. The net work is 800 kW with air mass flow rate of 5 kg/s. If the maximum temperature is 4000K and the temperature at the end of the isentropic compression is 1000K,find the heat added, efficiency and compression ratio

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION I Figure 1 shows cylinder block and piston of a reciprocating engine run with diesel fuel. The engine has displacement volume of 3000 cm and has clearance volume. Consider that the engine is a four-cylinder and four-stroke operates on the Diesel cycle with a compression ratio of 18 and cutoff ratio of 2. The pressure and temperature of air is at the beginning of the compression process is dependent on local ambient condition. Using constant specific heats at 500 K: i) decide working condition at the beginning of the compression process and calculate all the working temperature and pressure at all points on P-V diagram for the engine, ii) determine the net work output and the thermal efficiency, iii) determine the mean effective pressure, iv) develop expression of Power (P) as a function of rotational speed (N), and v) plot graph of Power versus Engine speed (RPM) for the above engine from 0 – 4500 rpm. Please provide complete table of Power versus Engine speed. What is the…
An ideal dual cycle has a compression ratio of 18 and a cut off ratio of 2.2. At the beginning of the compressions process, air is at 100kpa and 27 degree Celsius, while it is at 2200 degree Celsius at the end of the heat addition processes. Find the net work done by the cycle, thermal efficiency of cycle, and mean effective pressure.
Q3:A small truck has #cylinder ,4 liter compression ignition engine that operates on ir standard Dual cycle with air fuel ratio of 16:1, the compression ratio is 17 and the cylinder diameter is 14.5Cm. At the start of compression stroke Ta=50'C and Pa=100 kpa .It can be assumed the half of the heat input is added at constant volume and halt at constant pressure Calculate: 1-Temperature and pressure at each state of the cycle. 2-Indicated thermal efficiency. 4:28 PM
A four-stroke gasoline engine has a compression ratio of 10:1 with 4 cylinders of total displacement 2.3 L. the inlet state is 290 K, 90 kPa and the engine is running at 2400 RPM with the fuel adding 1500 kJ/kg in the combustion process. What is the network in the cycle and how much power is produced?
I need handwritten only otherwise skip I'll rate
If the Mean Effective Pressure (MEP) is the ratio of the net work and the volume displaced, find the MEP per kg of air in an Otto Cycle with initial conditions of 0.1 MPa, 306K; rk is ten and max temp is 3021R.
EX. 3: A petrol engine is supplied with a fuel of (41868 KJ/Kg) heating value. Cylinder pressure at (30%) of the stroke and (70%) of the stroke are (1.33 bar) and (2.66 bar) respectively. Assuming the compression isobying the Law PV=const. find the compression ratio if the relative efficiency compared with that of the ideal cycle is (50%). calculate the specific fuel consumption.
A simple Rankine cycle works betw een pressures 48 bar and 10 Kpa, the initial condition of steam being dry saturated. Calculate the cycle efficiency, work ratio and specific steam consumption.
The working fluid used to operate an ideal Stirling engine is helium with temperature limits at 313K and 2100K and pressure limits of 120kPa and 5 MPa. If the mass of the working fluid is 0.15kg, find: the thermal efficiency of the cycle, the amount of heat transferred in the regenerator, and the work output per cycle.