An electric pole design is shown below. The frame is used to carry high-voltage wires. If b=600 mm, a=30° and W=981 N, find the internal force in member HJ?

Q: In (Figure 1), P₁ = 12 kN and P₂ = 6 kN. Figure 2 m G B 1 m 2 m 1 m 1 of 1

A:

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

A: The given information in the problem is shown in the following attached image:

Q: Problem 2.2-23 A bridge structure is modelled by two hinge-connected girders which are supported in…

A: A bridge structure is modelled by two hinge-connected girders which are supported in A and B as…

Q: A straight and piecewise uniform bar ABCD of total length L is in Case 1 fixed at A in case 1 and in…

A: Given Data:- AB=BC=CA=L3 AABC=2ACBL=90cmE=70GpaACD=4cm2P=10KN To Find:-  Average normal stress &…

Q: The shaft is supported at its ends by two bearings AA and BB and is subjected to the forces applied…

A:

Q: A bent pipe is attached to a wall with brackets as shown. A force of F= 235 lb is applied to the end…

A: Given data:Force, F = 235 lba = 12 inb = 27 inc = 20.3 ind = 75 inh = 42.5 ing = 50 inAssume D is…

Q: 1. For the space trusses shown in figure, determine the stiffness matrix for each element. Let E =…

A:

Q: The rigid bar BCE is supported by two links AB and CD as shown in Figure 1. The Link AB is made of…

A:

Q: QUESTION 1 In the beam below, the member is held in equilibrium with a pin at A and a cable at B.…

A: F=46 Nuniform load w=24 N/mTo determine:Total reaction force at Pin A

Q: 4. The structure shown in Figure 4 is subjected to the force of 45 kN, which acts in a plane…

A:

Q: The tractor shovel shown (Figure 4) carries a 530 kgkg load that has its center of mass at H. The…

A: The tractor shovel shown (Figure 4) carries a 530 kg load that has its center of mass at H.The…

Q: C 30° 3 m 4 m B 98 200 N/m 100 N

A: Given,

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a - 2 ft • b = 4 ft C = 1 ft then,…

A:

Q: A truss structure is shown in Figure A1-1. The member AB is along the horizontal direction. A…

A: (a) To Find :  The reaction force at joint A and B. Free body diagram : F.B.D is shown below

Q: 5.5-5.15 For the rigid frames shown in Figures P5-5 through P5-15, determine the displace- ments and…

A:

Q: A frame structure, as shown in the following diagram, is given. Calculate: (a) Reaction forces at…

A:

Q: Consider the frame shown in Fig 4. A 100N load is suspended around a fixed drum with radius 2 m…

A: Draw the free-body diagram of the frame.

Q: The truss below is subject to the loads as shown. All of the members are attached at plates and can…

A: The normal force in member AE.Given:The applied loads are .The given truss is shown below.

Q: 10 10¹ D C 8 Fig.4 40° 8' B 5000 lb

A: Given : The free body diagram is,

Q: A truss structure is shown in Figure A1-1. The member AB is along the horizontal direction. A…

A:

Q: Figure -3 ft Figure -3 ft- < 1 of 1 M The bent rod is supported by a smooth surface at B and by a…

A:

Q: Find the tension in the cables and reaction force at point O.

A:

Q: A frame structure is shown in the following Figure. Members ABC and BD are pin jointed to supports…

A:

Q: Suppose that P₁ = 420 lb and P2 = 560 lb. (Figure 1) Figure G -4 ft- F B P₁ -4 ft- E C P₁ -4 ft- 4…

A: The forces in the members FBD:The free-body diagram of the section is shown below.

Q: A heavy spool rests on the ground at point A and against the wall at point B. Find force F required…

A: Given that, Mass of the spool, m=100 kg,Radius of spool, ri=200 mm, and ro=460 mm,Coefficient of…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.