An elasto-plastic material with strain hardening behavior has a stress-strain relationship composed by a linear elastic phase (E»10 MPa, O y=0.1 MPa) followed by a linear plastic phase with a slope of 1 MPa . Calculate the total strain that correspond to a stress of 0.3 MPa.

An elasto-plastic material with strain hardening behavior has a stress-strain relationship composed by a linear elastic phase (E»10 MPa, O y=0.1 MPa) followed by a linear plastic phase with a slope of 1 MPa . Calculate the total strain that correspond to a stress of 0.3 MPa.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

An aluminium specimen with an initial gauge diameter d, = 10 mm and gauge length, 1, = 100 mm is %3D subjected to tension test. A tensile force P= 50 kN is applied at the ends of the specimen as shown, resulting in an elongation of 1 mm in gauge length. The Poisson's ratio (µ) of the specimen is Take shear modulus of material, G = 25 GPa. Consider engineering stress-strain conditions. P
6.46 For some metal alloy, a true stress of 345 MPa e (50,000 psi) produces a plastic true strain of 0.02. How much does a specimen of this material elongate when a true stress of 415 MPa (60,000 psi) is applied if the original length is 500 mm (20 in.)? Assume a value of 0.22 for the strain-hardening exponent, n.
A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in. × 0.1220 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 98290 N (22100 Ib;) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 610 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa. (a) i (b) i (c) i mm
At an axial load of 22 kN, a 45-mm-wide by 10-mm-thick polyimide polymer bar elongates 2.7 mm while the bar width contracts 0.26 mm. The bar is 180 mm long. At the 22-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= i i i GPa mm
A bar of length 5.0 m is made of a structural steel having the stress-strain diagram shown in the Figure (a). The yield stress of the steel is 250 MPa and the slope of the initial linear part of the stress-strain curve (Modulus of elasticity) is 200 GPa. The bar is loaded axially untill it elongates 7.5 mm and then the load is removed. How does the final length of the bar compare with its original length?
A bronze rod is rigidly attached between an aluminum rod and a steel rod as shown in the figure below. Axial loads are applied at the positions indicated. a) Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in bronze of 100 MPa, or in aluminum of 90 MPa. b) Determine the deformation of the bronze rod if the value of P is 22.50 KN. The moduli of elasticity are 200 GPa for steel, 80 GPa for bronze and 70 GPa for aluminum.
A homogenous isotropic material of size 20 cm x cm x 20 cm is placed inside a rigid box of internal dimension 20 x 20 x 20 cm. The top of the box is open and the material inside is subjected to a uniform compressive stress of 10 N/mm² from the top. Assuming there is no friction between the surface of contact, find the stresses on the side faces of the material. Also find maximum shear stress, the normal stresses on the plane of maximum shear stress and the change of volume of the material. Young's modulus E is 1 x 105 N/mm² and Poisson's ratio, m = 0.3 for the material. S 10 N/mm² 20 cm 20 cm-
A 5-mm-thick rectangular alloy bar is subjected to ajtensile load P by pins at A and B, as shown in the figure. The width of the bar is w = 33 mm. Strain gages bonded to the specimen measure the following strains in the longitudinal (x) and transverse (y) directions: €, =710 με and ε,--255 με (a) Determine Poisson's ratio for this specimen. (b) If the measured strains were produced by an axial load of P = 24 kN, what is the modulus of elasticity for this specimen? Answers: (a) v= (b) E= GPa
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 740 mm. The cross-sectional dimensions of the beam are b1= 35 mm, d1= 101 mm, b2 = 21 mm, d2 21 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. %3D b2 M. d2 di 14 L. b1 Answer: N-m M = %3D
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 110 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam.
A bar of length 2.0m is made of a structural steel having the stress-strain diagram shown in the figure. The yield stress of the steel is 250 MPa and the slope of the initial linear part of the stress-strain curve (modulus of elasticity) is 200GPa. The bar is loadded axially until it elongates 6.5mm, and then the load is removed. How does the final length of the bar compare with its original length? (Hint: Use the concepts illustrated in figure below)
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 540 mm. The cross-sectional dimensions of the beam are b1 = 37 mm, d1 = 117 mm, b2 = 22 mm, d2 = 22 mm, and a = 7.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 10 MPa. Determine the largest moment M that can be applied as shown to the beam.