An axial load P is supported by a short steel column, which has a cross-sectional area of 11600 mm². If the average normal stress in the steel column must not exceed 130 MPa, determine the minimum required dimension "a" so that the bearing stress between the base plate and the concrete slab does not exceed 19 MPa. 239 mm 282 mm O 256 mm

An axial load P is supported by a short steel column, which has a cross-sectional area of 11600 mm². If the average normal stress in the steel column must not exceed 130 MPa, determine the minimum required dimension "a" so that the bearing stress between the base plate and the concrete slab does not exceed 19 MPa. 239 mm 282 mm O 256 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

An axial load P is supported by a short steel column, which has a cross-sectional area of 11200 mm². If the average normal stress in the steel column must not exceed 110 MPa, determine the minimum required dimension "a" so that the bearing stress between the base plate and the concrete slab does not exceed 15 MPa. O 185 mm O 313 mm O 287 mm O 206 mm O 239 mm
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 24 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number
Please help:)
A rigid steel plate is supported by three posts of high-strength concrete each having an effective cross-sectional area A = 40,000 mm2 and length L = 2 m (see figure). Before the load P is applied, the middle post is shorter than the others by an amount s = 1.0 mm. The allowable compressive stress in the concrete is 20 MPa and E of concrete is 30 GPa. What is the minimum load P (kN) needed to close the gap? P S
A) Determine the lateral strain B) Determine the axial strain C) determine the poisson’ts ratio V. COMPLETE SOLUTION. THANKS!
Asap Please with FBD thank you
PLEASE PROVIDE COMPLETE SOLUTION THANKS
Complete solution please thank you 4 DECIMALS Compute for the maximum tensile bending stress (in MPa). Compute for the maximum compressive bending stress (in MPa). Compute for the bending stress (in MPa) 2 m to the right of point A and 30 mm from the top of the beam. Find the maximum shear stress (in MPa) for the beam and cross-section. Compute for the shear stress (in MPa) 1.5 m to the right of point A and 50 mm from the top of the beam.
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly