An automobile tire is inflated to 38 psig at 70 F. After being driven, the temperature rise to 95 F. Determine the final gauge pressure, in psi, assuming volume remains constant.

Q: A certain cloud consists mostly of supercooled water droplets at -10°C and maintains the ambient air…

A: Write the expression of supersaturation.   s=C-CeqCeq×100%

Q: Refrigerant 134a inside an insulated piston-cylinder assembly initially occupies 0.017 m at 0.6 MPa,…

A:

Q: 2. Determine the clamping force on the bolt and reactions at pin A for the pliers shown.

A: It is required to determine the force on the bolt and reactions at pin A, given that the applied…

Q: In the diagram the ring is pulled down by two forces F and F2 to create a resultant force F, having…

A: a) The FBD of the figure is given below -

Q: Q4. If you have a rod with an initial diameter 12 mm, final diameter is 10 mm and yield stress…

A: Given: The initial diameter of the rod, di = 12 mm The final diameter of the rod, df = 10 mm The…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A:

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: The impacting jet for a Pelton turbine carries a flow of 0.5 m/s, and the jet is 7 cm in diameter.…

A: Given : Q = 0.5 m3/s d = 7 cm To find : Pressure of the fluid on impeller

Q: An ideal compressor compresses 12 kg/min of air isothermally from 99 kPa and a specific volume of 1…

A:

Q: Rigid bar ABC is supported by member (1), which has a cross-sectional area of 0.9 in.2, an elastic…

A:

Q: A capillary tube is to be selected to throttle 0.011 kg/s of refrigerant 22 from a condensing…

A:

Q: Example Problem has a 3.5-in. wide X 1/2-in. deep aluminum alloy plate securcly fastened to its…

A: For solution refer below images.

Q: Fixtures are used___ a•for holding and guiding the tool in drilling, reaming or tapping operations…

A: Jig-A jig is a device which is used to locates,support and guide the tool during cutting…

Q: Q#2: the condenser of Geothermal Heat Pump will be cooled by A pipe with dimeter 3 cm buried in a…

A: The given information-   Diameter d= 3 cm = 0.03 m Cooling load Q = 8 ton = 8 ×3.516 = 28.128 kW hs…

Q: 4. A 1.2 kg quarter circular plate with 0.20 m radius is welded to a 1.5-kg triangular plate to form…

A: The mass of the quarter circle,(m1)=1.2 kg The radius of the quarter circle,(R)=0.20 m The mass of…

Q: A full-load test was conducted on a two-stroke, 2-cylinder engine and the following results were…

A: The entire power created within the cylinder in one complete cycle, excluding any losses, is the…

Q: KPa and Is a erature is 696.54 C. Determine the change of internal energy in kJ.

A: GivenVolume=10m3Pressure P1=569.16kpaInitial Temperature T1=429.91KFinal…

Q: Find the magnitude, direction and centre of pressure (point of application) of the resultant force…

A: Given:Side of triangular hatch, S=0.5 mPosition of top of triangular hatch from the free surface,…

Q: Will upvote for immediate solution

A: To solve this problem, we need to analyze the forces acting on the cable and the chairs. We can…

Q: 15 m³/h water enters the turbine at 20°C and leaves it at 50°C. The internal diameter of the inlet…

A: Write the expression for SFEE for the given flow system.

Q: The force F(t) acts on a sled with mass m that is located on a frictionless incline with a 30°…

A: Given data: Fo=3mgFt1=0

Q: Water with mass of 2 kg (initial temperature of water is 10-degree C) and ice with mass of 6 kg…

A:

Q: A circumferential fin of rectangular cross section, 3.7-cm OD and 0.3 cm thick, surrounds a 2.5-cm-…

A: GIVEN• A mild steel circumferential fin of a rectangular cross section on a tube.• Tube diameter…

Q: The equipment room housing the compressor and condenser of a refrigerant ammonia system has…

A: Given:-  Room Size = 5 x 4 x 3 m, Refrigerant Ammonia, P=1atm=101.325Kpa, Toxic concentration for a…

Q: Find the work posses for a carbon dioxide gas at 711.62 C in kJ/kg. (Use W - mRT)

A:

Q: An aircraft has span efficiency factor = 0.7831, minimum drag coefficient = 0.025, wing area = 175…

A:

Q: 5. A 1.2 kg quarter circular plate with 0.20 m radius is welded to a 1.5-kg triangular plate to form…

A:

Q: A load of P = 88 kN is supported by a structure consisting of rigid bar ABC, two identical solid…

A: Given data  P = 88kN Eb = 80 GPa Es = 167 GPa db = 19 mm  ds = 29 mm  L1 = 3.5 m  L2 = 1.6 m c = 1.8…

Q: Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN.…

A: Condition #1   Given: The compression load, P = 20 kN The material used = SAE 1040 Hot rolled steel

Q: Consider the mechanism of Bar AB, Bar BC, and roller A. Roller A is constrained to move along the…

A: Consider the mechanism of Bar AB, Bar BC, and roller A. Roller A is constrained to move along the…

Q: Question 1 Choose corect statements related to the cold rolling process O Require greater loads O…

A: Cold rolling process requires greater loads due to strain hardening or work hardening of material by…

Q: 3. A homogeneous thin quarter circular plate with 0.20 m radius has a mass of 1.2 kg. Which of the…

A: The mass of quarter circular plate is 1.2 kg.

Q: 1.) For the mechanism shown, determine: X mm a. Linear velocity of point B. b. Angular velocity of…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.