An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 350 MPa, and at compression SuC = 1150 MPa. it carries static loading resulting in the stress state listed below at the critical locations. Using the static failure analysis estimate the factor of safety. OA = 160 MPa, oB = -224 MPa.

An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 350 MPa, and at compression SuC = 1150 MPa. it carries static loading resulting in the stress state listed below at the critical locations. Using the static failure analysis estimate the factor of safety. OA = 160 MPa, oB = -224 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A beam has fluctuating bending moment and is not rotating. The bending moment has a maximum of 1kNm and a minimum of 100kNm. The beam is made of AISI1020CD steel with a square cross section. There are no stress concentrations. a. Determine the fully corrected endurance limit as a function of the cross section (cross section unknown) b. Determine the required size for a factor of safety of 2 using the Gerber Fatigue Failure Theory
A point in a brittle material of ultimate strength equal to 600 MPa 0, and has the following state of stress: 0xx = 150 MPa, oyy Txy = 60 MPa. Determine the safety factor used in the design. =
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 61 % - Percentage of Reduction in Area = 43 % - Final length after fracture = 34.8 mm - Final Diameter after fracture = 4.2 mm & - Ultimate stress = 433 MPa Determine the Initial length, Initial diameter and Maximum load. SOLUTION: i) Initial Length (in mm) = Answer for part 1 ii) Final Area (in mm2) = Answer for part 2 iii) Initial Area (in mm2) = Answer for part 3 iv) Initial Diameter (in mm) = Answer for part 4 v) Ultimate Load (in N) = Answer for part 5
Q1) A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of Syt = 50 kpsi and Sye = 65 kpsi. Using the ductile Coulomb-Mohr theory, determine the factor of safety for the states of plane stress. 0x = 35 kpsi, and oy = 20 kpsi, Txy бу 0 Submit your answer in 4 significant digits. =
Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa. Using the distortion- energy and maximum-shear-stress theories, determine the factors of safety for the following plane stress states. 0x² =104 MPa, 0y = 19 MPa, and Txy = -19 MPa I The factor of safety from the maximum-shear-stress theory is 3.8 3.45 and the factor of safety from the distortion-energy theory is
Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa. Using the distortion- energy and maximum-shear-stress theories, determine the factors of safety for the following plane stress states. 0x = -46 MPa, Oy = -80.5 MPa, and Txy = -46 MPa The factor of safety from the maximum-shear-stress theory is 3.56, and the factor of safety from the distortion-energy theory is 3.3
A tensile-testing apparatus is to be constructed that must withstand a maximum load of 293516 N. The design calls for two cylindrical support posts, each of which is to support half of the maximum load; the minimum yield and tensile strengths of this alloy are 343 MPa and 565 MPa or 82,000 psi respectively.what is required diameter? Take factor of safety is 2.3
A soft steel specimen has a BHN of 150, find the equivalent 29 tensile strength in MPa. A. 393 B. 503 C. 443 D. 533 What is the value of strain at yield point of 1-inch diameter C1030 as rolled steel in the stress-strain curve? A. 0.0012 B. 0.0015 C. 0.0017 D. 0.0022 A copper column of annular cross section has an outer diameter of 0.5 m. and is subjected to an axial loading of 5 kips. The allowable compressive stress is 2 ksi. Compute the wall thickness. A. 1.15 m B. 2m C. 0.8 m D. 1 m
Part A and B circle final answers The next 2 question relate to the modified Goodman diagram with the following baseline data. A part is made from steel with the following properties: Ultimate tensile strength is 450 MPa Yields stength is 260 MPa Fully-corrected endurance limit is 180 MPa The part is subjected to a time-varying load with σmax = 150 MPa and σmin = 90 MPa . Part A The safety factor with respect to fatigue is?? Part B - the safety factor with respect to yielding is?
Factor of safety??
For a 1040 steel solid square bar, determine the endurance limit or Se based on the following information describing the loading condition, reliability factor, etc.
Required information A shaft is loaded in bending and torsion such that M₂ = 66 N-m, T₂ = 42.496 N-m, Mm = 51.858 N-m, and Tm - 33 N-m. For the shaft, Su = 700 MPa and Sy=560 MPa, the true fracture strength is 1045 MPa, and a fully corrected endurance limit of S₂ = 210 MPa is assumed. Let Kf= 2.2 and Kfs=1.8. With a design factor of 2.0, determine the minimum acceptable diameter of the shaft using the methods mentioned in the subsection. Determine the minimum acceptable diameter of the shaft using the DE-Morrow criterion. The diameter of the shaft is mm.