An amplifier consists of 8 identical stages with resistive loads. The amplifier was designed to provide the minimum possible rise time for the given amplifier gain. Consider the stage device model as shown below. Find: a. The amplifier gain b. The load resistance c. If the amplifier rise time is less than 30 ns, what is the minimum value of Co? d. The bandwidth of the amplifier Co ? Cj = 4pF -3 4 (10) mhos Im %3D

An amplifier consists of 8 identical stages with resistive loads. The amplifier was designed to provide the minimum possible rise time for the given amplifier gain. Consider the stage device model as shown below. Find: a. The amplifier gain b. The load resistance c. If the amplifier rise time is less than 30 ns, what is the minimum value of Co? d. The bandwidth of the amplifier Co ? Cj = 4pF -3 4 (10) mhos Im %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

You are tasked with designing a linear amplifier using an NPN BJT for the circuit shown below. This means the transistor iv curves apply here. The voltages given are Vcc = 14 V and Vs = 1.0 V. The datasheet for the transistor says VBE (ON) = 0.7 V,VCE (SAT) = 0.2 V, and ß = 400. The design should have ic = 12 mA and VCE = 8 V. Find the resistances Rb and Rc that give the required ic and VCE. Vs H Rb M d VBE Rc VCE Vcc
this is CC(common collecter ) amplifier.why it is a cc circuit, you can get the answer from its AC circuit.so now PLS draw its AC and DC circuit. plz solve it early
4. Is it possible to get a gain less than unity using a non-inverting amplifier configuration? If yes, sketch a circuit.
3- A microwave amplifier for cellular applications is being tested for linearity. The input to the amplifier is the sum of two sinusoidal waveforms at the frequencies of 860 MHz and 870 MHz, with an input power spectrum that looks like the figure on the left below. It is determined that the output power spectrum looks like the figure shown on the right (other components are filtered out). a) What is the value of the linear power gain of the amplifier? b) What is the value of the output IP3 for this amplifier? c) What is the value of the input IP3 for this amplifier? d) What is the max linear (fundamental) output power that can be obtained (in each of the two equal amplitude sinusoids) to keep the third order intermodulation products at a power level of 40 dB below the linear output power? e) What is the max. input power than can be used? -50 dBm -25 dBm output input -60 dBm 850 860 870 880 frequency 850 860 870 880 frequency
11. What is the configuration of the given amplifier circuit below?12. How are the coupling capacitors treated in the figure of #11 at AC?
Consider the integrating amplifier circuit in Figure 2. Using nodal analysis, derive an expression for vout for the integrating amplifier. In the circuit in Figure 2, exchange the positions of the 0.1uF capacitor and the 5k resistor. a. Use nodal analysis to generate an expression for vout. b. Using this expression, explain what function this circuit performs on an input signal.
Question 7) Design a JFET amplifier network with ldss-8 mA, Ve=-4 V, R1=110 MN, R2=10 MQ. When an input AC signal V=10 mV is applied to the network, an output signal Vo=2V AC is obtained. (suppose that ra2 10R0) a) Draw the JFET amplifier network you prefer to design, and explain why you choose this network b) Explain the aims and reasons in using of all the peripheral components handled on your network c) Draw AC equivalent re model of the network (5p.) d) Draw transfer characteristic curve and derive lda and Vasa values from the characteristic curve e) Calculate Av, gm, VoD, Ro, Rs, Z; and Zn. Note: Please, do not forget using resistors and capacitors as peripheral elements whatever required for your complete design in the question (i.e. input, output terminals etc.)
Figure 2 shows a typical BJT amplifier, with its parasitic capacitances displayed. The current gain of the transistor is B=150 and the voltage gain of the amplifier is Am =-125. The small signal resistances of the transistor are re =16 ohm and r0 = infinity, respectively. The values of resistors and capacitors in the figure are: R1 =80 kohm, R2 =20 Kohm, Rc = 2 Kohm, RE = 2 Kohm, Rs =50 W, RI=5 kohm, Cs=2 uF, Cc=2 uF, Ce =10 uF, Cbc =4 pF, Cbe = 10 pF, Cce =1 pF, Cwi = 4 pF, CWO = 9 pF, and Vcc = 20 V. a) Sketch a simplified circuit diagram of Figure 2 for high frequency analysis. b) Using the concept of "Miller effect capacitance", calculate the input and Output Miller effect capacitances of Figure 2, respectively. C) Determine the upper cut-off frequency of Figure 2 that is imposed by its input network only. d) Explain briefly the possible ways to increase the upper cut-off frequencv of this amplifier.
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
Please solve with steps, using to study. Will upvote!
In an emitter-biased transistor circuit, we have collector source voltage V CC = 15 V, collector resistance RC = 3.5 kOhm, emitter voltage V_E = 4.3 V and emitter current LE = 2.1 mA. If the current gain is 150, what is the difference in emitter-collector voltage V_CE when we calculate it including the gain factor vs when it is calculated by assuming collector current LC = LE? Select one: O a. 3.35 V O b. 3.40 V OC 0.05 V O dov