An amplifier circuit containing resistor R1) is shown in the circuit below: an OpAmp (with extra input

Q: 1. Construct the logic gates and obtain its final output stream. B. (rO f)s + (5 +t)r

A: Given: The logic expression is Y=r⊕ts¯+s¯+tr¯

Q: +2v ou +180 (b)

A:

Q: Determine V,, Vs(pk), Vupk), Vdc, PIV, and fout. Draw also the output waveform with the voltage…

A:

Q: 3. The transistor in the following circuit is operating at VDs = 2 V. Find the operating region with…

A:

Q: How the armature reaction works in a de generator.

A: When Armature current flow in the Armature conductor, it generates a additional Flux inside the…

Q: Briefly explain the working of following power plants a) Thermal Power plant b) Hydel power plant

A: thermal power Plant coverts heat energy to electric power / Energy. The basic principle of these…

Q: hi please answer. thanks

A: 3) a) Break even point=Total fixed costRevenue per unit-Variable cost per unit Revenue per unit,…

Q: Figure P6.1-1 shows Fourier spectra of signals gi(t) and g2 (1). Determine the Nyquist interval and…

A:

Q: Question: A capacitive displacement sensor, which works by measuring change in capacitance from the…

A:

Q: Briefly explain about a) Primary transmission b) Secondary transmission c) Primary distribution d)…

A: Given: The two stages of transmission The two stages of distribution

Q: Calculate the current flowing in the 10-ohm resistor using combination circuits and equivalent…

A:

Q: A plane wave is normally incident on a dielectric slab of permittivity e, and thickness d, where d =…

A:

Q: A bandpass signal g(t) of bandwidth B= 2000 Hz centered at f= 10³ Hz is passed through the RC filter…

A: Given: A bandpass signal g(t) of bandwidth B=2000 Hz centered at f=105 Hz is passed through the RC…

Q: Q3. 5 points Use the mesh-current method to find the pha- sor current I in the circuit shown.…

A:

Q: 6. Evaluate the voltages at all nodes and the currents through all branches. Assume: VBE (or VEB for…

A: Given:

Q: Determine the Nyquist sampling rate for the following signals: (a) 4 sinc(420πt); (b) 5 sinc²…

A: As per Bartleby guidelines, as more than 3 subparts are present in the question, only the first 3…

Q: For the filter shown below, with an input signal whose PSD is given by S₂(f)= II(0.25πf): (a) Find…

A: I have written this solution as handwritten solution. Hope you find the solution clear.

Q: 17. In a certain company, an all day study revealed the following noise sources: 0.42 hrs., 112 dBA;…

A: The most common types of natural sound sources direct and include: road traffic noise, airplane…

Q: The AS-I bus network, O a. does not support Ob. supports analog data. QUESTION 7 The most powerful…

A: The AS I bus network________analog data. The most powerful hierarchy among industrial applications…

Q: Question 1 For the three-stage amplifier shown below, given that: Rs 10 k2, 38 Ri1 = xy k2, Ro1 = 1…

A:

Q: Determine the output y(t) and generate a plot of both the input, x(t) and the output y(t). The…

A:

Q: Question 2 Find the gain value for: a) vo/vs (V/V) b) volis (V/A) in the circuit below given that:…

A:

Q: (a) Consider the signal f(t) = e-t defined on the interval t € [0, 1]. Find the exponential Fourier…

A:

Q: ca) Compute tne fourier toamsform of each of the follocsing signals. ci) xcn) = co25u[n-1] ci) Hgcn)…

A: As per our guidelines we are supposed to be answer the first question only.  Kindly repost the other…

Q: 1. A majority circuit is a combinational circuit whose output is equal to 1 if the input variable…

A:

Q: Determine the input signal x2(n) if the convolution output is Y(w) with x1(w). (Hint: do not include…

A:

Q: # 10. For the next two questions, consider the common emitter amplifier below with beta=100 and…

A: We need to find out output voltage and input voltage for bjt saturation region .

Q: FIND V(t) Y/₁₂F= + 32H શો નૈન V(t) + 4 cos (3+ +150) 34H Ssin(St) (+-)

A:

Q: Problem- A single phase induction motor draws 12 MW power at 0.6 lagging power factor. A capacitor…

A: Given- Single phase induction motor- Power P1=12 MW, Power factor cosϕ1=0.6 lagging, Improved power…

Q: Find Norton equivalent circuit for the terminal across R5 resistor. R₁ i R3 R₂ R₁ I V3 R5

A:

Q: Determine the power and energy for each of the following signals. (a) x[n]=(0.5n +0.2n)u[n] (b)…

A: In this question,  Two signals are given.  Find the energy and power of the given signals.

Q: Three very long current-carrying wires are arranged as shown in the figure. What is the force per…

A: We need to find force on bottom wire .

Q: 3. Discuss the principle of commutation process to produce de 'out put generator. in de

A: In this question we discuss about the principle of commutation process to produce DC output in DC…

Q: Under DC conditions, find the energy stored in the 20uF capacitor in micro Jules. 3 ΚΩ ww 10 V…

A: it is asked to find the energy stored and capacitor voltage

Q: Obtain the transfer function H(s) = Vo/V₁. Suppose vi(t) = V₁cos(wt). Obtain the steady state…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: The conduction band is closest to the valence band in Select the correct response: semiconductors…

A:

Q: For a simple resistive potential divider, the CRO rating of oscilloscope is 250 V. For the…

A: Amplification ratio is, α=1175 and 1050 Therefore, R1R2=α-1       =1175-1       =1174 and R1R2=α-1…

Q: b) For the 4-bit bidirectional shift register, determine the state of the register after each clock…

A:

Q: B. Use SUPERPOSITION THEOREM to determine lab. 2 volt 22 22 ЗА 2 volt ЗА 1 volt 12

A:

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.