Urgent solution needs An ammeter having a measurement range of 0* 15 A is installed to monitor the current of a motor. Iheanalog value of current is converted into 4-bit binary number using a converter, corresponding to theammeter current in steps of 1 A. The 4-bit binary number is then fed into a logic unit. The output of thelogic unit is an alarm which shail trigger in the following conditions:1. When the value of current is s 3 A.H. when the value of current is 2 10AIn view of the above:a) Draw a block diagram showing an ammeter, a converter and a logic unit.bị State the Truth lable.c) write down the expression in sum-of-products expressian and smplify the expression.di Draw the Ingic diagram of the simplified function

To convert the input value from analog ammeter an analog to digital converter with 4-bit output is…

An ammeter havng a measurement range ofo* 15 A is installed to monitor the current of a motor. Ihe analog value of current is converted into 4-bit binary number using a converter, corresponding to the ammeter current in steps of 1 A. The 4-bit binary number is then fed into a logic unit. The output of the logic unit is an alarm which shalil trigger in the following conditions: . when the value of current is s 3A. H. when the value of current is 2 10A In view of the above: a) Draw a block diagram showing an ammeter, a converter and a logic unit. bị State the Truth lable. c Write down the expression in sum-of-products expression and smplify the expression. Draw the Ingic diagram of the simplified function

An ammeter havng a measurement range ofo* 15 A is installed to monitor the current of a motor. Ihe analog value of current is converted into 4-bit binary number using a converter, corresponding to the ammeter current in steps of 1 A. The 4-bit binary number is then fed into a logic unit. The output of the logic unit is an alarm which shalil trigger in the following conditions: . when the value of current is s 3A. H. when the value of current is 2 10A In view of the above: a) Draw a block diagram showing an ammeter, a converter and a logic unit. bị State the Truth lable. c Write down the expression in sum-of-products expression and smplify the expression. Draw the Ingic diagram of the simplified function

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
Discuss the principles of grid resilience and how advanced sensors and communication technologies contribute to grid reliability during extreme events.
In the medium voltage air line network given in the figure,a) Draw the protection scheme of one of the transformers connected in parallel together with the protection controls as three poles.b) Construct a protection system with overcurrent time relays with a minimum opening time of 0.5 s and time steps of 0.5 s.
Electrical Engineering A 240V single phase circuit is run in conduit in 2 core 70°C PVC/PVC cable having live a) conductor of 2.5 mm (leperating is approximately 20A) and protection conductor cable (cpc) of 1.5 mm If the circuit is protected by 30 HRC fuse, with circuit length of 55 m, and Zg is 0.8 0 EVALUATE whether the initial cip.c. size provided is adequate. Given 2 core PVC/PVC bunched cable impedance is (R +R2) 26.9 m2/m and k -115.
(c) Figure Q5(c) shows a without and with guard circuit of a Megger insulation resistance instrument. The instrument supplies a test voltage of 15 kV. The measurement without a guard terminal provides a current of 6.1 µA, while the current decrease to 1.1 µA when using a guard terminal. Determine the following: (i) The volume resistance of the cable insulation, ry. (ii) The surface leakage resistance, rs. (d) Discuss the important of guard-wire method in a high resistance measurement.
How does a wide-area monitoring system (WAMS) contribute to the stability and control of large-scale power grids?
How to verify the validity of the nodal analysis technique in solving electrical networks?
2. What is the difference between single-phase controlled and three-phase controlled circuits?
Needs validation please 333
Explain the concept of pumped hydro storage and its role in grid stabilization.
The voltage drop percentage for a panel feeder with a no continuous load of 180A, using 3/0 THWN copper conductors at 480V, three-phase, and a length of 248' is
14/ Coupling Capacitors are used to prevent High Frequency Low Power Communication Signals leaking into the Power System Transformers. Select one: True False