An A36 W14X605 simply supported steel beam with span L=13.5m carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). Calculate the nominal moment strength in stronger axis? Express your answer in KN-m in 2 decimal places.

An A36 W14X605 simply supported steel beam with span L=13.5m carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). Calculate the nominal moment strength in stronger axis? Express your answer in KN-m in 2 decimal places.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.4P

See similar textbooks

Similar questions

A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
The beam under the Live and Dead loads is shown below. The steel class is $235. Lig L1 L2 a.) Evaluate the slenderness of the web and flange. b.) Calculate the Cb value based on the loads. c.) Calculate the bending moment capacity of the beam... d.) Is the beam cross-section enough for the given loads. L3
The beam shown in Figure is laterally braced at A, B, C, and D. Is a W18 × 119 adequate forFy = 50 ksi?a. Use LRFDb. Use ASD.
ASSIGNMENT #5 BIAXIAL BENDING Problem: Check the beam shown for compliance with the NSCP Specification. Lateral support is provided only at the ends, and A992 steel is used, F, = 345 mPa. The 90 kN service loads are 30% dead load and 70% live load. a. Use LRFD b. Use ASD d tw by ty 1x(106) S(10³) mm mm mm mm³ mm mmª W410x100 415 10 260 16.9 398 1920 SECTION Tx mm 177 1m 90 kN 90 KN 1.5m W410x100 I Loaded Section Ly(106) Sy(10³) Ty mmª mm³ mm 49.5 381 62.4 1m Zx(10³) Zy(10³) mm³ mm³ 2130 581
A simply supported beam is subjected to a uniform service dead load of 1.0 kips/ft (including the weight of the beam) and uniform service live load of 2.5 kips/ft. The beam is 40 feet long, The beam has continuous lateral support, and A572 Grade 50 steel is used. A572 Grade 50 steel has Fy = 50 ksi and Fu = 65 ksi. Is a W30 × 116 adequate from flexure and shear?Check both LRFD and ASD. Is the beam adequate from deflection if it allowsmaximum deflection of L/360 (dead load + liveload)?
A simply supported beam is subjected to a uniform service dead load of 15kN/m(including the weight of the beam), a uniform service live load of 30kN/m. the beam is 12 meters long and is laterally supported at the midspan, and A572 Gr.50 steel is used. Is W30x108 adequate? Assume Cb=1 by 4 d fore k h h Z S Ly 267 TH mm 19.3 757 13.8 min m 35.8 685.4 54.6 737.7 5670 x10^3 4900 x103 mm 60.8 x10 6 mm 2080 x10 3 8300 x10^9 mm www
i need the answer quickly
A simply supported A992 W14x61 30-foot length beam has a concentrated load, P, and it’s midspan. P is a service live load. What is the maximum permissible value of P. Use LRFD, then use ASD. You can assume that the beam has continuous lateral support. Manually verify that the beam is compact. Don’t forget to account for self-weight
The beam shown is simply supported and has lateral support only at its ends. The only service dead load is the weight of the beam. Determine whether it is satisfactory for the load shown. A992 steel (E= 345 MPa and F= 450 MPa) is used, and the 30 KN/m is a service live load. Use LRFD 30 KN/m WiL = 30 KN/m W16x 40 -Centroid W16 x 40 3m
The below figure represents a section of a pre- stressed beam. For a no-tension design where a is the permissible stress in concrete, the total moment carrying capacity is (a) (c) d/2 bd² 6 d/2 bd²oc 3 -b- (b) (d) bd² oc 4 bd²a 12
Use Allowable Strength Design. Use A992 steel and select a W-shape for the following beam: • Simply supported with a span length of 40 feet • Laterally braced only at the ends • Service dead load = 0.4 kips/ft • Service live load = 1.2 kips/ft • The service dead load consists of a 10 kip concentrated load at the center of the span. • The service live load consists of a 30 kip concentrated load at the center of the span. There is no limit on the deflection.