An A36 Channel compression member of 2.06m length is laterally supported at mid-length on its major axis and at third points on its minor axis. The member has fixed supports at both ends. The properties of the channel section: A=1135mm2 , Ix=0.86x106 mm4 , Iy=0.13x106 mm4 . Calculate the maximum Slenderness Ratio of the member. Express your answer in 2 decimal places.

An A36 Channel compression member of 2.06m length is laterally supported at mid-length on its major axis and at third points on its minor axis. The member has fixed supports at both ends. The properties of the channel section: A=1135mm2 , Ix=0.86x106 mm4 , Iy=0.13x106 mm4 . Calculate the maximum Slenderness Ratio of the member. Express your answer in 2 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What will be the safe weight per linear meter length of the beams if the displacement at E is limited at 8mm. Where x=14.37m. = Properties of Steel: Ast 300mm², Est-200 GPa, Lst=2m = Properties of Steel: Aal 500mm², Eal-70 GPa, Lal=2m 0:5X Whit ALUMINUM x STEEL с
a w12x65 column section shown in the figure is pined at each end and has an additional support in the weak direction at a point 4.19m from the top. Use x = 4.71 K=1 A = 12323 rx = 134.11 ry = 76.71 Fy = 248 Determine the a) design compresive strength (KN) b.) Elastic critical buckling stress (MPa) c.) Flexural buckling stress D.) Critical slenderness ratio E.) Nominal compressive stress F.) allowable compressive strength
A beam is built-up from the following A36 plates: 420x20 plates as flanges and 500x20 plate as web. The beam is simply-supported and subjected to concentrated load at midspan. The member is laterally supported at the ends only. Limiting L Values:Lp = 4.762 mLr = 11.810 m Section Properties:A = 27200 mm2Ix = 1 370 026 667 mm4Sx = 5 269 333.333 mm3rx = 224.430 mmIy = 246 960 000 mm4Sy = 1 176 000 mm3ry = 95.286 mmJ = 3 626 666.667 mm4c = 1.0 (doubly symmetric I-shaped member)rts = 110.753 mmho = 520 mm Compute for the ultimate moment capacity (in kN-m) of the beam if it spans 4m. Please answer this asap. For upvote Thank you so much
For the given properties of beam below. Compute the flexural capacity of the beam. b = 390mm d = 440mm d' = 80mm fc' = 34.5MPA fy = 350MPA As = 4 - 40mm As' = 2 - 32mm A. USE NSCP 2001, Mu = kN-m B. USE NSCP 2015, Mu = kN-m
6
Q) for UB 914x305x201, S460 steel, and ALT = 77.5, find bending strength Pb? ((from tables * 220 MPa 215 MPa 205 MPa O ¹176 MPa 208 MPa 202 MPa 188 MPa O
4
Please double check your answer in allowable stress and allowable loads. Please double check your answer
3. Determine maximum strength P for the bracket connection in the figure. ST37 steel is used for the connection, F = 2400kg /cm,F, = 3700kg /cm %3D %3D IPE200 15 cm P=? PL 250x150x15 mm te 7 mm, L=250 mm
An A36 Channel compression member of 2.88m length is laterally supported at mid-length on its major axis and at third points on its minor axis. The member has fixed supports at both ends. The properties of the channel section: A=1135mm2 , Ix=0.86x106 mm4 , Iy=0.13x106 mm4 . Calculate the maximum Slenderness Ratio of the member. Express your answer in 2 decimal places.
PLEASE DRAW THE FBD. DO NOT COPY YOUR ANSWER FROM OTHER. I WANT TO SEE THE FBD OF INDIVIDUAL DEFORMATIONS ON HOW YOU WILL ARRIVE ON YOUR ANSWER. DRAW FBD ON EACH PLEASE. NOT ONLY ONE FBD