An 8 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart (Figure P5.9).. After a 2.11 kN force has been applied, the separation between the lines has increased to 10.006 cm. (a) Calculate the stress and strain in the rod. (b) To what total length has the rod stretched? 30 cm 10 cm F -F 10.006 cm

An 8 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart (Figure P5.9).. After a 2.11 kN force has been applied, the separation between the lines has increased to 10.006 cm. (a) Calculate the stress and strain in the rod. (b) To what total length has the rod stretched? 30 cm 10 cm F -F 10.006 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The Poisson ratio formula for an auxetic structure given in the figure is given as follows: H = 8 cm L = 4 cm α = 50 ° t = 5 mm The strain value of the structure in the same direction as a result of the pull applied in the X axis from the bottom was measured as 0.26 mm / mm. Under the same loading condition: a) Calculate the strain on the Z axis of the structure. b) In this case, what is the strain type of the structure in the Z axis?
2.5
A 50-mm diameter cylinder is made of a brass for which the stress-strain diagram is as shown. The angle of twist is 5° in a length L = 725 mm. The three points on the nonlinear stress-strain diagram used are (0, 0), (0.0015, 55 MPa), and (0.003, 80 MPa). By fitting the polynomial T = A + By + Cy² through these points, the following approximate relation has been obtained. T= 46.7 × 10%y-6.67 × 1012/2 Determine the magnitude Tof torque applied to the shaft using this relation and the two equations given below. Y Ty - ρφ T (MPa) 2π ζ ρ?τὰρ 100 80 60 40 20 0 0.001 0.002 0.003 Y d = 50 mm L The magnitude T of torque applied to the shaft is kN.m.
Two forces are applied to a flywheel 50 cm in diameter. Each force is 500 N. The shaft is fixed to the wall using three grade 5 steel bolts. The distance between the bolts and the axis of rotation is 10 cm. (a) What moment of resistance must develop the three bolts together Answer: 250 Nm (b) What is the resistance force F of each bolt? Answer: 833.3 N (c) What is the diameter of the bolts if their factor of safety is 10? Answer: 4.14mm
Figure Q4(a) shows the stress-strain curves of material A and material B. A circular rod of material A (diameter 3 cm, length 10 cm) is bonded to a circular rod of material B (diameter 4 cm, length 20 cm) as shown in Figure Q4(b). a) Based on the stress-strain curves shown determine the yield stress (σy) and the elastic modulus (E) of material A and material B.b) Assuming that the bond is rigid, determine the force P required to stretch the composite rod by 0.3 mm?c) Assuming a Poisson’s ratio value of 0.33, determine the change in diameter of the rod made from material B for the same P as determined in part (b).
Please solve it asap !! Strictly don't use Artificial intelligence tools.
Figure 2 shows a bar with a length L fixed at the left end. Question 2 The uniformly distributed force f (unit: N/m) is applied along the axis of the bar, and a concentrated force P (unit: N) is applied at the free end of the bar. The bar has a constant Young's modulus E and cross-section area A. Find the stretch of the bar: (a). at the free end of the bar; (b). at the center of the bar. (Expressing all the resulta with E, A, L, f, and P). E, A L Fig. 2. The kft end of the bar is fd, ad the froe ed of the bar is applied with a force P. The uniformly distribatod kece f is applied akong the ais of the bar.
Question 1 The cube in Figure Ql made of 200 mm sides of a certain material is subjected to a volumetric stress of 50 N/mm?. Determine the change in its volume if the Bulk modulus of the material is 100x10° N/mm?. 200 mm Figure Q1: Cube subjected to volumetric stress
2. A compound bar of length 500 mm consists of a strip of aluminium 50 mm wide and 25 mm thick and a strip of steel 65 mm wide x 20 mm thick rigidly joined at the ends. If elastic modulus of aluminium and steel are 1 × 105 N/mm² and 2 × 105 N/mm², calculate the stresses developed in each material and the extension of the compound bar when axial tensile force of 60 kN acts.
Please don't copy paste
SECTION B- STRUCTURES-DR LARISA MALYSHEVA QB1 DIRECT STRESS Two round solid bars of different materials are connected (in parallel) and have a common tensile force, P, of 190 kN is applied,ras shown in Figure QB1. For each bar, determine the: a) b) Stress. Strain and Strain in the diameter. Use the following information. Clearly show all your derivations. The original length of each bar = 1.7m. %3D Steel Bar: 32mm Dia. Poisson's Ratio = 0.31 18mm Dia. Young's Modulus = 210 GPa %3D Steel Aluminium Bar Bar Common Connection Aluminium Bar: P = 190 kN Poisson's Ratio = 0.34 Young's Modulus = 68 GPa Fig QB1