ameter and 1.50 meter high contain oncrete (s= 2.0) at a depth of 1.20 me hat will be the amount of concrete s ers when rotated accidentally at the 20 rpm?

Q: A round vertical steel tank has an inside diameter of 3 m and is 6 m in height. It contains gasoline…

A: Given data, Inside diameter D = 3 m Height of cylinder  h = 6 m Gasoline density p = 750 kg/m^3…

Q: 3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2.…

A:

Q: A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate…

A:

Q: Calculate the maximum torque that can be applied.  b. If that bar were to be left hollow, with the…

A:

Q: An aluminum cylinder and a bronze cylinder are centered and secured between two rigid slabs by…

A:

Q: An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure,…

A: Stress normally the same direction fropm the force that makes it acts in a direction parallel to the…

Q: 1. A steel section of length L sits on an 8" x 8" bearing plate. The bearing plate is perfectly…

A: To determine,A. Determine the normal stress in the steel.  B. Determine the normal stress in the…

Q: A beam from the exterior balcony of a house has a base of 300 mm and a height of 500 mm reinforced…

A: Given: b = 300 mm h = 500 mm fc = 20.7 MPa fy = 415 MPa Main bars = 6-16mm bars stirrups = 12 mm…

Q: Knowing that P = Q = 480 N, determine (a) the distance a for which the absolute value of the bending…

A:

Q: a compound cylinder is to be made by shrinking one tube on to another so that the radial compressive…

A: Given : radial compressive stress at the junction = 28.5N/mm2 outside diameter = 26.5cm bore…

Q: A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the…

A:

Q: CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between…

A:

Q: a concrete beam simply supported at both ends 300 × 600mm it stressed by 3 cables of 700 mm each…

A: given data: ps =1200n/mm2                     e=100mm, ec =30,000

Q: A round concrete column has a diameter D.A force of 800 kN act on the column as shown. The yield…

A: Diameter = 50.46 mm

Q: The height of the capillary rise of water increases as particle diameter increases True O False O…

A:

Q: Only considering stresses that are normal to the cross-sections you're designing. Where omax is the…

A:

Q: a)Calculate the 5N force, the Vicker Hardness measurement with one corner of the pyramid trace 5mm…

A:

Q: A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb. The center of…

A:

Q: A flat annular steel disc of 0.8 m outside diameter and 0.15 m inner diameter is to be shrunk around…

A: Pressure is defined as the force that crosses a “small” boundary in each unit area of ​​that…

Q: working stress of mild steel is millimotore using

A: working load is given in question w = 150 KN factor load = working load x load factor Pu = P × load…

Q: Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long,…

A: Given for smallest cross-section,σ2=20 MN/m2=20×106 N/m2We know that, σ2=PA2So, P=…

Q: A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate…

A:

Q: a.) What is the normal force distributed to Stainless Steel Solid Post 'A' (in kips)? b.)What is…

A: Determine the normal stress developed in the stainless steel solid post 'A' and red brass hollow…

Q: (4) Two kids (200 N each) are balanced on a seesaw. Plane a-a (containing Point A) is just left of…

A: Data given Find : combined state of stress at two points A and B

Q: Find the limiting peripheral velocity of a rotating steel ring if the allowable stress is 20 ksi and…

A:

Q: 1.) A STEEL WIRE 30 ft LONG HANGING VERTICALLY SUPPORTS A LOAD OF 500 lb. 30 ft NEGLECTING THE…

A: Given,The length of the steel wire,L=30ftLoad is,P=500lbThe elongation is,δ=0.20 inchE=29×106 Psi

Q: A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate…

A:

Q: Determine the cracking moment for the figure shown if it is a normal weight concrete with…

A: We have to determine the value of cracking moment for the given beam in the figure according to the…

Q: 1. what is the axial stress in the bronze rod (MPa)?

A: "Since you have posted multiple questions. We will solve the first question for you. To get the…

Sediment transport

Sediment transport or Soil transport is the movement of solid particles, usually due to the combination of gravitational forces acting on the sediment, and the movement of the liquid at which the sediment enters. Soil erosion occurs in natural systems where the particles are sandstones (sand, rocks), mud, or clay; the liquid is air, water, or ice; and the gravitational force that works to move particles to the landing surface. Sediment transportation or soil migration due to the movement of liquids occurs in rivers, lakes, lakes, oceans, and other bodies of water as a result of currents and waves. Transportation is also caused by glaciers as they flow, and to places on earth under the influence of wind. Soil erosion due to gravity alone is possible in most sloping areas, including hills, scarves, cliffs, and the continental shelf — the continental boundary of the slope.