am 15kN 35 3m IDKN am Initial FBD Final FBD Find the reactions. Fill in the blank's Draw and label the final free body diagram. Ağ. By

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A:

Q: 嗎! 可 CCC

A: The image depicts an ancient Egyptian scene, likely illustrating some form of craft or technological…

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: 7) It is a P-Chart or C - Chart that is also called the number of defective per sample area.

A: Given Data- Statement about P-Chart and C-Chart given , we have to tell correct choice among P or C…

Q: 1. Draw the Front View, the Sectional Side View AA and the Top View of the object shown. 010 A 20 20…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: A .  Based on the electrical material properties, what will you choose to manufacture the rotor…

A: A.) Do make the rotor windings out of copper, which is the material to utilise for making such…

Q: Required information Three blocks A, B, and Cand a grooved block D have dimensions a, b, c, and das…

A: Calculated the mean gap and it's tolerance .

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: 97SD Make freehand sketches of any four (in all) common tools, utensils or pieces of furniture . 1.

A: Table is a furniture. Thus, sketch table:

Q: can you please write it in a proper way?

A:

Q: Develop two possible hierarchies for assembling a model from the parts given below: Top Pins…

A: Given question: Develop two possible hierarchies for assembling a model from the parts given below:…

Q: The shortest distance between a line and a point is achieved when? a) A line is drawn at 90 degrees…

A: Given  The shortest distance between a line and a point is achieved when? a) A line is drawn at 90…

Q: In drawing process, tensile forces are used to reduce the cross section of the workpiece. Select…

A: The drawing process is generally is done at the room temperature. To reduce the required forces, it…

Q: arc o C.

A: STEP-1 First draw the one arc from origin O1 with radious of 20mm ( AB)  And then draw the another…

Q: · How might your machine or system be improved? What constraints might be involved in its design?

A: Each interaction has a requirement and zeroing in progress endeavors on that limitation in the…

Q: What company specification number is given to the material for this part?  2. What is the revision…

A: First of all , this engineering drawing shows the detailed assembly drawing of KM50 Head with the…

Q: a)Prepreg formation results in   Tape consisting of randomly oriented fibers Sheet consisting of…

A: Since you have posted multiple independent Multiple choice questions. We will solve the first…

Q: I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps…

A: 13.The Maximum Material condition is the size of the part which contains the maximum amount of…

Q: Scenario 1: One mole of an ideal, monatomic gas runs through a four step cycle. All processes are…

A:

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: Consider the Material Selection Design Problem of the FRAME of an Exoskeleton Design for…

A: To explain:Evaluate the following alternatives based on your criteria, and justify your selection…

Q: 8 - A robot is used for loading and unloading of parts to automated flexible machines. Loading time…

A: Write the given data. tmachine=15 min        C1=30 TL/hour        C2=40 TL/hour Here, tmachine is…

Q: Q) Derivation of law( Tribology) h = c(1 + cose)

A: Derivation of law( Tribology)The position of the journal in a simple plain bearing is directly…

Q: I don't understand due to the way its written, can it be written again but more clearly pls

A: From the question, the given data are: Volume of heater = Capacity of heater =V1 =  2 liters = 2 x…

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: Draw me CAD drawing of a airplane

A: CAD drawing of an aeroplane is required.

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: Engineering Drawing: Dimensions

A:

Q: In wire drawing process, the cross sectional area of wire is reduced. Select one: True False

A: In wire drawing, Material is extruded .

Q: 1. An engineering manufacturing company has established that the relationship between the quantity…

A: Given: Quantity solved per month or demand per month=D And sales price for each product=p And demand…

Q: d) Determine the obtuse angle between F1 and F2 using the dot product. Provide Find, Problem…

A:

Q: how do i draw sectional view of this object.

A: A sectional view of an object is used to identify the parts interior construction of a part…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: AutoCAD is one of the ready-made that help workers in the field of design and engineering drawing…

A: in AUTO CAD we draw and edit the 2D or 3D modelings

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.