All question pertain to the following floor plan. The floor load is 60 lb/ft?. Ignorethe self weight of the members. The building is three stories tall.I-I-GZ20 10!C2B130'22 What is the value in kips of the point load in the middle of girder G1?

Given: w=60lb/ft2 Calculate the point load in the middle of girder G1: Before calculating you need…

Answered: All question pertain to the following…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Reinforced Concrete Design Determine the required spacing of 2 legged 12mm diameter stirrups at a distance "d" and "2h" from the top of rafter CD. Use b=300mm, d=625mm, h=700mm, fc'=35MPA, Grade 420 rebars.column is 600mmx600mm. Use simplified calculation and National Structural Code of the Philippines (NSCP 2010) 85 N/m 75 k/m 1-70 85m ir 88M 8 8m
I need the answer to the question in reinforced concrete
A spiral column is 430 mm in diameter and is reinforced with 7-28 mm bars Grade 415. The spirals are 10 mm in diameter and concrete cover used is 40 mm. If f'c = 28 MPa, and the column has an unsupported length of 2.20 m, what is the safe ultimate load that the column can support using the 2001 NSCP specifications? Neglect moment in the column. Ku = 1.0
2- The floor system shown above design to support service live load=4 kN/m? and total dead load = 10 kN/m?. Can the column (B) of dimension and detail shown below support the ultimate load of this slab and 1800 kN from upper stories. Assume: the column is short tied, f = 30 MPa and fy = 400 MPa. cover for all side =40mm 4Ø 25 mm 400 mm Ø 10mm@400mm 400 mm
A rectangular cross section of a beam is under the bending moment of 60 kips-ft. Determined the Maximum compression and tension stress in the concrete and tensile stress in the rebar. The section is uncracked. b-15 in, h=30 in, d= 28 in f=4000 psi, Ec-3,600,000 psf fy= 60,000 psi, Es-29,000,000 psf Rebar= 3 -No. 6 h -As
NEED IN 1 HR PLEASE, THANK U A beam of circular cross-section is 7 inches in diameter. It is simply supported at each end and loaded by two concentrated loads of 20,000 lbs each, applied 12 inches from the ends of the beam. Determine the maximum bending stress in the beam.
STRUCTURAL ANALYSIS II The given plan below shows a 2-way floor system carried by 1-story 2-bays frame system as shown in sec 1-1. The floor is 18 cm in thickness and made with reinforced concrete with fc'= 28MPA and fy= 420MPA, yc= 24kN/m3. The floor is to carry a service live load of 5 kN/m2. Assume that E is constant for all structural elements in the system. Determine the following: 1- Extract he structural system of beam ADG, beam BEH, frame ABC, and frame DEF, showing the loads to be carried on each element from the slab, and include the own weight of the element given that beams ADG and BEH have a section of 180mm in depth and 400 mm in width. Where the girder of all frames has a cross section of 300 mm in depth and 800mm in width. 2- Analyze beam ADG using slope- deflection equations method. 3- Analyze beam BEH using moment distribution method. 4- Analyze frame ABC using moment distribution method. G H 3 5m 5m 7m 7m Floor Plan 4m 7m 7m sec 1-1 800mm 400mm 300mm 180mm sec 2-2…
A floor slab 100 mm thick is cast monolithically with beams 250 mm wide 450 mm deep spaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports a service live load of 2.1 kPa. Using f.-21 MPa, rebar strength f, 415 MPa, calculate the following if a typical interior beam is reinforced with 3- 16-mm-dia. flexure bars at the bottom enclosed with 10-mm-dia. stirrups: 1. Nominal moment capacity (kN-m) of a typical interior beam in positive bending considering T-beam geometry. A. 96.66 C. 91.10 Maximum factored uniformly distributed load (kN/m) a typical interior B. 86.99 D. 81.99 2. beam can sustain against positive bending. В. 27.83 с. 26.23 D. 29.15 A. 30.93 3. Maximum service superimposed dead load in kPa. A. 17.73 C. 16.52 B. 11.08 D. 14.77
Calculate the factored moment strength of the slab below. If the only dead load the slab has to handle is its own self-weight, how much service live load can the slab hold? For finding this make the moment strength you calculate equal to Mu and solve for the possible live load using a factored load equation. f'c = 3000 psi, fy = 40000 psi A A -Span for design = 12'-0"– clear #8 @ 6" 0.c. Section A-A 8"
Plss, i need the answer immediately. Consider a two-bay building frame ABCDEF, with A, B, and C as fixed supports, AD, BE, and CF as columns, and DE and EF as girders. Span DE is 5.9 meters long and span EF is 6.8 meters long. The columns have a height of 10.5 meters. Assume that the columns have same cross-sections. A wind-induced lateral load of 80 kN is applied at D, pointing towards the structure. Additionally, a-wind induced uniform load of 1.5 kN/m, pointing upwards, is applied at the girders. (a) Draw the free-body diagram of the structure.
.
True or false, the load on a column for my particular floor depends on the tributary area of the column on the floor?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

All question pertain to the following floor plan. The floor load is 60 lb/ft?. Ignore the self weight of the members. The building is three stories tall. I- I- GZ 20 10! C2 B1 30' 22 What is the value in kips of the point load in the middle of girder G1?